Control Panel Messages, Format | Paradyne 3551 specification

Status Indicators and Control Panel Messages

Control Panel Messages

This section shows the screen format of messages appearing on the control panel and describes the various messages.

Three types of messages are included: health and status, progress, and error messages.

Format

The format of the control panel messages is shown below.

Command Name

Message

F1 F2 F3

Health and Status Messages

There are three types of health and status messages. Device Health and Status messages are described in Table C-3, Expanded Health and Status messages are described in Table C-4, and Subnetwork Health and Status messages are described in Table C-5.

Table C-3

(1 of 3)

Device Health and Status Messages

Message			Condition

CMI Fac Alarm	Facility Alarm on CMI (FacAlOnCMI) configuration option is enabled and control mode
	idle (CMI) is being received.

Config Corrupt	Configuration is corrupt. Reset all configuration options from one of the default
	(factory-loaded) option sets stored in the PTPC, PTPT, MPTC, or MPTT.
DBM:Device Fail	Internal failure is detected in the DBM.

DBM:Disable	DBM transmitter is disabled. DBM is in Idle mode, but no calls can be initiated or
	answered.
nn.nDBM:mode	nn.n indicates the DBM speed; mode is one of the following:
	Standby	Ð A dialed connection is made, but the data is still routed over the DDS
			circuit. The first line shows the dial backup connection time.
	Active	Ð A dialed connection is made, and data has been routed over that line.

nn.nExternBU	nn.n indicates the external DBU's speed:
	External	Ð	Backup is in progress on an external DBU. (DDS line is
	Bkup		disabled.)

DBMTst: test,init	The DBM is running a test, initiated from init.
	test is one of the following tests:
	BERT	Ð Bit Error Rate Test
	BiL	Ð	Bilateral Loopback
	Dev	Ð	Device Test
	DL	Ð	Digital Loopback
	DT	Ð	Digital Test
	DTE	Ð	DTE Loopback
	E-E	Ð	End-to-End Test
	Lamp	Ð	Lamp Test
	RL	Ð	Remote Digital Loopback
	TM	Ð	Test Mode
	init is one of the following initiators:
	DTE	Ð	Data T erminal Equipment
	FP	Ð Front Panel (the DCP)
	NMS	Ð	Network Management System
	Remt	Ð	Remote DSU

3550-A2-GB20-20

December 1996

C-3

Image 107

Paradyne 3551 manual Control Panel Messages, Format, Health and Status Messages

Contents

Comsphere 3550 Series Data Service Units Models 3550 Copyright 1996 Paradyne Corporation. All rights reserved Warranty, Sales, and Service InformationTrademarks Important Safety Instructions CC DGD D C D CC Interface Data Rate Code Bps Government Requirements Comsphere 3550 Series Data Service Units Table of Contents Glossary Index List of Figures List of Tables Hubbing Device CC IN/DC OUT Jack Pin Assignments About This Guide How to Use This GuidePreface Reference Documents Related Documents Overview Standard FeaturesAbout Your DSU 32 DBM Optional Features Port TDM/Flex Upgrades AvailableTechnical Specifications CSA Specifications Criteria DSU Heat Dissipation MAX. AT 115 VAC Lads DSU Technical Specifications DOC DBM Technical Specifications Criteria Port TDM/Flex Technical Specifications Equipment Warranty Support Before You Begin Installing the Model 3550 DSU Procedure How to Change Hardware Straps Permissive V.32 DBM transmit output level of ±9 dBm Installing the DSU Where to Place the DSU Power-Up Routine Connecting to the Network Connecting to the Dial or Pstn Network Connecting to the NMS Model 3550 DSU DDS Lads Network Connection Connecting to the DDS or Lads Network Addressing the Unit Lads Connection Distances Data Rate Wire Gauge AWG Kbps Addressing Example Tributary DSU Addressing Installing Cables Connecting the DSU to a DTE Verifying the Network Verifying Operation and Testing ConnectionsConnecting Port Verifying Network Addresses Other Tests Verifying DBM OperationVerifying TDM/Flex Operation Installing the Model 3551 DSU Before You Begin Off Strap State Function Designation Jumper Strap Model 3551 DSU Jumper Straps Comsphere 3000 Series Carrier, Rear View Model 3551 DSU Installation and Circuit Pack Lock V.35 Interconnect Cable Installation Connecting to Dial or Pstn Network Connecting to DDS or Lads Network Verifying Operation and Testing Connections Verifying Network Addresses, the Network, and DBM Operation To Connect the Sdcp to a DSU Other Tests Operating the DSU DCP and Sdcp Operation Model 3550 Diagnostic Control Panel Sdcp and Model 3551 DSU Faceplate Keypad Top-Level Menu Status BranchMenu Structure Health and Status Identity Terminal PowerDTE Status Circuit Quality Identity Descriptions Backup BranchDial Backup Operation Configuring the Unit for Dial Backup Auto Bckup ± Select Enab Understanding Operating Modes Manual DDS Restoration Manual BackupPlacing a Backup Call Manual Dial Backup Termination Loopback Test BranchAbort Device Test Remote Digital Loopback Bilateral LoopbackDTE Loopback Digital Loopback End-to-End Test Bit Error Rate Test Lamp Test Configuration BranchSelecting Menu Mode Bit Error Rate Test Results Information Displayed Selecting an Application Configuration Reconfiguring a TDM/Flex Port Configuration OptionsReconfiguring a DSU Port Changing the Poll List Poll ListDisplaying the Poll List Q u i r P o l l L i s t Abort Acquiring the Poll List Entering a Telephone Number Directory Assigning an Address Directory Entry and Password Characters UsePhone Network Address External Leads Control BranchTransmitter Control LEDs Reporting External Lead Changes to NMS Lead States SymbolMessages Branch Front Panel DCP Security Security Access LevelsSecurity Functions Available Access Level Configuring the Unit Editing Configuration Values Using the DCP to Set Configuration Options Example Using the DCP Saving Configuration Options Ptpc Understanding the Tables Configuration Option Tables DDS DSU Configuration Options Support a Transmit Elastic Store Diagnostic DSU Configuration Options Diagnostic DBM Configuration Options Diagnostic General Configuration Options Diagnostic External DBU Configuration Options DTE operation RXC DBM Configuration Options Disab Select disable if you do not have an extended network DSUs and DBMs If DTR is low DCE External DBU Configuration Options =RTS General Configuration OptionsDTE Select to ignore the Loopback command Signal is dropped DTE asynchronous data rate Backup Configuration Options TriesTimeOut period expires DSD MUX Setup Configuration OptionsMUX Port Configuration Options 1800 Select the rate of the asynchronous port Configuration option Receiver Carrier Select Messages to the DSU Port Speed DSU Configuration Options Port Speed DBM Configuration Options Port Speed External DBU Configuration Options Port1 DSU 9.6 C Local Remot Msg DSU Menu a Comsphere 3550 Series Data Service Units DSU Menu Local branch Local/Remote Menu Subbranches Overview Instructions Configuration Worksheets B Model 3550 or 3551 DSU Configuration Worksheet 1 Model 3550 or 3551 DSU Configuration Worksheet 2 Full Menu Mode Disabled Port Speed DSU Value Status Indicators Status Indicators and C Control Panel Messages Label Color Description DSU Status IndicatorsSdcp Status Indicators Table C-1 Table C-3 Device Health and Status Messages Condition Control Panel MessagesFormat Health and Status Messages Table C-3 Device Health and Status Messages Condition Pnnn Tst test,init Message Condition Failnreason Table C-4 Expanded Health and Status Messages Condition MUX Table C-5 Subnetwork Health and Status Messages ConditionDTR Progress Messages Command Progress MessagesTable C-7 Dial Backup Progress Messages Condition Table C-8 Command Error Messages Condition Action Error Messages DBM Table C-10 TDM/Flex Error Messages Condition Action Prt2 Table C-10 TDM/Flex Error Messages Condition Action Pin Assignments D Figure D-1. Digital Network Connector Hubbing Device Table D-1Pin Circuit Function GND DCOSD/CCIRDDCORD/CCISD DCOCTS/CCIRTS DCORTS/CCICTS OUT DCOSD/CCIRD Comsphere 3550 Series Data Service Units SBB SBA Figure D-4. V.35 Interconnect Cable 3000-F1-510 Cable Circuit Name Pin Number Figure D-5. EIA-232-D Crossover Cable 4951-035F Figure D-6. V.35 Crossover Cable 3211-178F Point-to-Point Applications Application Configurations E Comsphere 3550 Series Data Service Units Multipoint Applications Figure E-2. Multipoint Application Configurations Comcode = Factory InstallEquipment List Equipment Comsphere 3000 Series Carrier, Installation Manual Equipment Part Number Pin-to-Pin EIA-232 Cable straight connection 10 i Ð Active core Glossary CSA DOC LDM RTS TXD Index Index-2 Configuring unit DSD Index-5 MUX Index-7 SDCP, C-2 Index-9