Maxtor 88400D8 Power Requirements Average, Power Mode Definitions, EPA Energy Star Compliance

Page 19

PRODUCTSPECIFICATIONS

Power Requirements (Average)

MODE

12V ± 8%

5V ± 5%

POWER

 

 

 

 

Spin-up (peak)

1070 mA

390 mA

14.0 W

 

 

 

 

Seek

530 mA

415 mA

8.5 W

 

 

 

 

Read/Write

255 mA

445 mA

5.0 W

 

 

 

 

Idle

250 mA

250 mA

4.0 W

 

 

 

 

Standby

2 mA

140 mA

0.7 W

 

 

 

 

Power Mode Definitions

Spin-up

The drive is spinning up following initial application of power and has not yet reached full speed.

Seek

A random access operation by the disk drive.

Read/Write

Data is being read from or written to the drive.

Idle

The drive is spinning, the actuator is parked and powered off and all other circuitry is powered on. The drive is capable of responding to read commands within 40 ms.

Standby

The spin motor is not spinning. The drive will leave this mode upon receipt of a command that requires disk access. The time-out value for this mode is programmable. The buffer is active to accept write data.

EPA Energy Star Compliance

Maxtor Corporation supports the goals of the U.S. Environmental Protection Agency’s Energy Star program to reduce the electrical power consumption of computer equipment.

Environmental Limits

PARAMETER

OPERATING

 

NON-OPERATING/STORAGE

Temperature

5° C to 55° C

 

low temperature (-40° C) per MIL-STD-810E, method 502.3.

 

 

 

high temperature (71° C) per MIL-STD-810E, method 501.3,

 

 

 

climatic category; hot-induced conditions.

 

 

 

 

Thermal Gradient

 

25° C per hour (maximum)

 

 

 

 

Relative Humidity

 

5% to 95% (non-condensing)

 

 

 

 

Wet Bulb

 

 

27° C (maximum)

 

 

 

 

Altitude

-200 to 10,000 feet

 

Per MIL-STD-810E, method 500.3, low pressure (altitude) test

 

(with any naturally occurring

 

procedure I. storage; test condition 2, transport aircraft cargo

 

temperature and humidity rate within

 

compartment pressure.

 

this range)

 

 

 

 

 

 

Acoustic Noise (Idle mode)

37 dBA average sound power

 

 

 

(per ISO 7779, 10 microphone)

 

 

 

 

 

 

3 – 3

Image 19
Contents DiamondMax REV EC no Section Description Date U T I O N Before You BeginContents Handling and Installation Product SpecificationsAT Interface Description Host Software Interface Service and Support Interface CommandsGlossary Figures Abbreviations IntroductionMaxtor Corporation Manual OrganizationNumbering Signal ConventionsConventions Key WordsProduct Description DiamondMax 2160 Key FeaturesFunctional / Interface Product FeaturesSoftware ECC Correction On-the-Fly Hardware Error Correction Code ECCLogical Block Addressing Defect Management Zone DMZAutomatic Write Reallocation AWR Read-Ahead ModeCache Management Buffer SegmentationMajor HDA Components Dual Drive Support Subsystem ConfigurationJumper Location/Configuration Cylinder LimitationModels and Capacities Product SpecificationsDrive Configuration Performance SpecificationsOutline and Mounting Dimensions Physical DimensionsParameter Standard Metric Environmental Limits Power Requirements AveragePower Mode Definitions EPA Energy Star ComplianceShock and Vibration Reliability SpecificationsStandard Test Methods Safety Regulatory ComplianceImportant Notice Handling and InstallationHard Drive Handling Precautions Pre-formatted DriveMulti-pack Shipping Container Unpacking and InspectionRecommended Mounting Configuration Physical InstallationRepacking Master Device Slave Device Drive Jumper SettingsInstalling 5.25-inch Mounting Brackets Mounting Drive in SystemMounting Drive in 5.25-inch Bay Inch InstallationMounting Drive in 3.5-inch Bay IDE Interface and Power Cabling Detail Attaching IDE Interface and Power CablesSystem Interface Card Cabling Attaching System CablesSystem Mother board Cabling Setting the Bios Cmos System SetupSet the Bios Cmos parameters as follows Model CYL SPT System Hangs During BootSystem/Drive Information Hard Drive PreparationPin Description Summary Interface ConnectorData Connector AT Interface DescriptionPin Description Table PIN Name Signal Name Signal DescriptionPIO Data Transfer To/From Device PIO TimingMulti-word DMA Data Transfer DMA TimingInitiating an Ultra DMA Data In Burst Ultra DMA TimingSustained Ultra DMA Data In Burst Host Pausing an Ultra DMA Data In BurstHost Terminating an Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In BurstSustained Ultra DMA Data Out Burst Initiating an Ultra DMA Data Out BurstHost Terminating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out BurstDevice Terminating an Ultra DMA Data Out Burst Task File Registers Error RegisterFeatures Register Host Software InterfaceDevice/Head Register Sector Count RegisterSector Number Register Cylinder Number RegistersCommand Register SDH Command Name Command Code Parameters UsedTimer Value TIME-OUT Period SummaryDigital Input Register Control Diagnostic RegistersAlternate Status Register Device Control RegisterReset Handling Reset and Interrupt HandlingInterrupt Handling Set Feature Commands Interface CommandsRead Sectors Read CommandsRead Verify Sectors Read Multiple Read DMAWrite Verify Sectors Write CommandsSet Multiple Mode Write SectorsWrite DMA Write MultipleSet Features Mode Set Feature CommandsValue Description Power Mode Commands Timer Value TIME-OUT Period Word Content Description Initialization CommandsIdentify Drive Word Content Description = Write Cache enabled Initialize Drive Parameters Format Track Seek, Format and Diagnostic CommandsExecute Drive Diagnostic Error Code DescriptionExecute S.M.A.R.T A.R.T. Command SetSupport Service and SupportService Policy No Quibble ServiceInternet MaxFax ServiceBulletin Board Service Customer Service

82160D2, 84320D4, 2160, 83240D3, 86480D6 specifications

Maxtor, known for its innovative storage solutions, produced several pivotal hard drive models during the late 1990s and early 2000s, namely the Maxtor 88400D8, 86480D6, 83240D3, 2160, and 84320D4. Each of these drives showcased unique features and technologies that catered to various computing needs.

The Maxtor 88400D8 stood out with its impressive storage capacity of 8.4 GB, which was considerable at the time. It employed the IDE interface, ensuring broad compatibility with most personal computers. The drive utilized a 5400 RPM spindle speed, optimizing data transfer rates for everyday applications. With a 2 MB cache, it facilitated smoother data retrieval, making it a reliable choice for both home and office use. This model exemplified Maxtor's commitment to enhancing user experience through advanced technologies.

Another noteworthy model, the Maxtor 86480D6, offered an 8.6 GB storage capacity, predicated on similar design principles as the 88400D8. It also featured a 5400 RPM spindle speed and an IDE interface. Its greater data density further improved performance, reducing the time required for searching and accessing large volumes of information. The 86480D6 was particularly favored by users with intensive storage needs, such as graphic designers and multimedia creators.

The Maxtor 83240D3, with a storage capacity of 3.2 GB, catered to users seeking a balance between performance and size. This drive also operated at 5400 RPM and featured an IDE interface. Its compact size made it an attractive option for entry-level systems and budget-conscious consumers who needed dependable storage without excessive capacity.

The Maxtor 2160 and 84320D4 models further diversified the line with distinct features suitable for different user segments. The 2160 offered 2.1 GB of storage, appealing particularly to users of basic office applications. In contrast, the 84320D4 provided 4.3 GB of space, marking a mid-range option for users requiring additional capacity without leapfrogging into high-end solutions.

All these Maxtor models incorporated technologies enhancing reliability and performance, such as Advanced Format technology, which optimized data organization, ensuring efficient use of storage space. These drives also showcased an emphasis on low power consumption, which aligned with growing concerns over energy efficiency in computing.

In summary, the Maxtor 88400D8, 86480D6, 83240D3, 2160, and 84320D4 were crucial entries in the hard drive market, bringing forth features that addressed the diverse needs of users, from casual consumers to professionals demanding superior performance. Their legacy continues to influence hard drive design and performance standards in contemporary storage solutions.