Maxtor 88400D8, 86480D6, 84320D4, 83240D3, 82160D2 specifications Timer Value TIME-OUT Period

Page 55

INTERFACECOMMANDS

When enabling the Automatic Power Down sequence, the value placed in the Sector Count register is multiplied by five seconds to obtain the Time-out Interval value. If no drive commands are received from the host within the Time-out Interval, the drive automatically enters the STANDBY mode. The minimum value is 5 seconds.

TIMER VALUE

TIME-OUT PERIOD

0

Time-out disabled

 

 

1 - 240

(value * 5) seconds

241 - 251

((value - 240) * 30) minutes

 

 

252

21 minutes

 

 

253

Vendor unique period = 10

 

hours

254

Reserved

255

21 minutes, 15 seconds

While the drive is in STANDBY MODE, any commands received from the host are accepted and executed as they would in normal operation, except that the spin motor is started if required to execute a disk command. Under these conditions, the drive will set BSY when command processing would normally begin and will leave BSY set until the drive comes up to speed and the disk command can be executed. Disk commands issued while the drive is in STANDBY MODE, restarts the Time-out Interval after completing the command. A reset must be issued before attempting to issue any commands while the drive in

SLEEP MODE.

7 – 8

Page 54 Page 56
Image 55
Page 54 Page 56
Contents DiamondMax REV EC no Section Description Date U T I O N Before You BeginContents Handling and Installation Product SpecificationsAT Interface Description Host Software Interface Service and Support Interface CommandsGlossary Figures Abbreviations IntroductionMaxtor Corporation Manual OrganizationNumbering Signal ConventionsConventions Key WordsProduct Description DiamondMax 2160 Key FeaturesFunctional / Interface Product FeaturesSoftware ECC Correction On-the-Fly Hardware Error Correction Code ECCLogical Block Addressing Defect Management Zone DMZAutomatic Write Reallocation AWR Read-Ahead ModeCache Management Buffer SegmentationMajor HDA Components Dual Drive Support Subsystem ConfigurationJumper Location/Configuration Cylinder LimitationModels and Capacities Product SpecificationsDrive Configuration Performance SpecificationsOutline and Mounting Dimensions Physical DimensionsParameter Standard Metric Environmental Limits Power Requirements AveragePower Mode Definitions EPA Energy Star ComplianceShock and Vibration Reliability SpecificationsStandard Test Methods Safety Regulatory ComplianceImportant Notice Handling and InstallationHard Drive Handling Precautions Pre-formatted DriveMulti-pack Shipping Container Unpacking and InspectionRecommended Mounting Configuration Physical InstallationRepacking Master Device Slave Device Drive Jumper SettingsInstalling 5.25-inch Mounting Brackets Mounting Drive in SystemMounting Drive in 5.25-inch Bay Inch InstallationMounting Drive in 3.5-inch Bay IDE Interface and Power Cabling Detail Attaching IDE Interface and Power CablesSystem Interface Card Cabling Attaching System CablesSystem Mother board Cabling Setting the Bios Cmos System SetupSet the Bios Cmos parameters as follows Model CYL SPT System Hangs During BootSystem/Drive Information Hard Drive PreparationPin Description Summary Interface ConnectorData Connector AT Interface DescriptionPin Description Table PIN Name Signal Name Signal DescriptionPIO Data Transfer To/From Device PIO TimingMulti-word DMA Data Transfer DMA TimingInitiating an Ultra DMA Data In Burst Ultra DMA TimingSustained Ultra DMA Data In Burst Host Pausing an Ultra DMA Data In BurstHost Terminating an Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In BurstSustained Ultra DMA Data Out Burst Initiating an Ultra DMA Data Out BurstHost Terminating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out BurstDevice Terminating an Ultra DMA Data Out Burst Task File Registers Error RegisterFeatures Register Host Software InterfaceDevice/Head Register Sector Count RegisterSector Number Register Cylinder Number RegistersCommand Register SDH Command Name Command Code Parameters UsedTimer Value TIME-OUT Period SummaryDigital Input Register Control Diagnostic RegistersAlternate Status Register Device Control RegisterReset Handling Reset and Interrupt HandlingInterrupt Handling Set Feature Commands Interface CommandsRead Sectors Read CommandsRead Verify Sectors Read Multiple Read DMAWrite Verify Sectors Write CommandsSet Multiple Mode Write SectorsWrite DMA Write MultipleSet Features Mode Set Feature CommandsValue Description Power Mode Commands Timer Value TIME-OUT Period Word Content Description Initialization CommandsIdentify Drive Word Content Description = Write Cache enabled Initialize Drive Parameters Format Track Seek, Format and Diagnostic CommandsExecute Drive Diagnostic Error Code DescriptionExecute S.M.A.R.T A.R.T. Command SetSupport Service and SupportService Policy No Quibble ServiceInternet MaxFax ServiceBulletin Board Service Customer Service

82160D2, 84320D4, 2160, 83240D3, 86480D6 specifications

Maxtor, known for its innovative storage solutions, produced several pivotal hard drive models during the late 1990s and early 2000s, namely the Maxtor 88400D8, 86480D6, 83240D3, 2160, and 84320D4. Each of these drives showcased unique features and technologies that catered to various computing needs.

The Maxtor 88400D8 stood out with its impressive storage capacity of 8.4 GB, which was considerable at the time. It employed the IDE interface, ensuring broad compatibility with most personal computers. The drive utilized a 5400 RPM spindle speed, optimizing data transfer rates for everyday applications. With a 2 MB cache, it facilitated smoother data retrieval, making it a reliable choice for both home and office use. This model exemplified Maxtor's commitment to enhancing user experience through advanced technologies.

Another noteworthy model, the Maxtor 86480D6, offered an 8.6 GB storage capacity, predicated on similar design principles as the 88400D8. It also featured a 5400 RPM spindle speed and an IDE interface. Its greater data density further improved performance, reducing the time required for searching and accessing large volumes of information. The 86480D6 was particularly favored by users with intensive storage needs, such as graphic designers and multimedia creators.

The Maxtor 83240D3, with a storage capacity of 3.2 GB, catered to users seeking a balance between performance and size. This drive also operated at 5400 RPM and featured an IDE interface. Its compact size made it an attractive option for entry-level systems and budget-conscious consumers who needed dependable storage without excessive capacity.

The Maxtor 2160 and 84320D4 models further diversified the line with distinct features suitable for different user segments. The 2160 offered 2.1 GB of storage, appealing particularly to users of basic office applications. In contrast, the 84320D4 provided 4.3 GB of space, marking a mid-range option for users requiring additional capacity without leapfrogging into high-end solutions.

All these Maxtor models incorporated technologies enhancing reliability and performance, such as Advanced Format technology, which optimized data organization, ensuring efficient use of storage space. These drives also showcased an emphasis on low power consumption, which aligned with growing concerns over energy efficiency in computing.

In summary, the Maxtor 88400D8, 86480D6, 83240D3, 2160, and 84320D4 were crucial entries in the hard drive market, bringing forth features that addressed the diverse needs of users, from casual consumers to professionals demanding superior performance. Their legacy continues to influence hard drive design and performance standards in contemporary storage solutions.
Top Page Image Contents