Maxtor 6800 manual Before You Begin, U T I O N

Page 3

Before You Begin

Thank you for your interest in the Maxtor DiamondMax™ 6800 AT hard disk drives. This manual provides technical information for OEM engineers and systems integrators regarding the installation and use of DiamondMax hard drives. Drive repair should be performed only at an authorized repair center. For repair information, contact

the Maxtor Customer Service Center at 800-2MAXTOR or 408-922-2085.

Before unpacking the hard drive, please review Sections 1 through 4.

1

2

3

4

5

C A U T I O N

Maxtor DiamondMax 6800 hard drives are precision products. Failure to

follow these precautions and guidelines outlined here may lead to

product failure, damage and invalidation of all warranties.

BEFORE unpacking or handling a drive, take all proper electro-static discharge (ESD) precautions, including personnel and equipment grounding. Stand-alone drives are sensitive to ESD damage.

BEFORE removing drives from their packing material, allow them to reach room temperature.

During handling, NEVER drop, jar, or bump a drive.

OnceadriveisremovedfromtheMaxtorshippingcontainer, IMMEDIATELYsecurethedrive through its mounting holes within a chassis. Otherwise, store the drive on a padded, grounded, antistaticsurface.

NEVER switch DC power onto the drive by plugging an electrically live DC source cable into the drive's connector. NEVER connect a live bus to the drive's interface connector.

Please do not remove or cover up Maxtor factory-installed drive labels.

They contain information required should the drive ever need repair.

Image 3

Contents HA RD Drive Produc T MA Nual DiamondMax U T I O N Before You BeginContents Handling and Installation Product SpecificationsHost Software Interface AT Interface DescriptionInterface Commands Service and SupportGlossary Figures Abbreviations IntroductionMaxtor Corporation Manual OrganizationNumbering Signal ConventionsConventions Key WordsProduct Description DiamondMax 6800 Key FeaturesFunctional / Interface Product FeaturesSoftware ECC Correction On-the-Fly Hardware Error Correction Code ECCLogical Block Addressing Defect Management Zone DMZAutomatic Write Reallocation AWR Read-Ahead ModeCache Management Buffer SegmentationMajor HDA Components Dual Drive Support Subsystem ConfigurationJumper Location/Configuration Cylinder LimitationModels and Capacities Product SpecificationsDrive Configuration Performance SpecificationsParameter Standard Metric Physical DimensionsEnvironmental Limits Power RequirementsPower Mode Definitions EPA Energy Star ComplianceShock and Vibration Reliability SpecificationsSafety Regulatory Compliance Radiated Electromagnetic Field Emissions EMC ComplianceCanadian Emissions Statement Important Notice Handling and InstallationHard Drive Handling Precautions Pre-formatted DriveMulti-pack Shipping Container Unpacking and InspectionPhysical Installation Recommended Mounting ConfigurationRepacking Drive Identification Information Handling PrecautionsTools for Installation System RequirementsHard Drive Identification General RequirementsMounting Drive in System Systems Using Cable SelectInstalling 5.25-inch Mounting Brackets and Rails Installing in a Device BayAttaching System Cables Attaching Interface and Power CablesSystem Setup Setting the Bios CmosBios Cmos Parameters Hard Drive Preparation System Hangs During Boot Interface Connector AT Interface DescriptionPin Description Summary Pin Description Table PIN Name Signal Name Signal DescriptionPIO Timing Timing Parameters ModeDMA Timing Ultra DMA Timing Mode MIN MAXSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Task File Registers Error RegisterFeatures Register Host Software InterfaceDevice/Head Register Sector Count RegisterSector Number Register Cylinder Number RegistersCommand Register Summary Command Name Command Code Parameters Used SDHDigital Input Register Control Diagnostic RegistersAlternate Status Register Device Control RegisterReset and Interrupt Handling Reset HandlingInterrupt Handling Set Feature Commands Interface CommandsRead Commands Read SectorsRead Verify Sectors Read Multiple Read DMAWrite Verify Sectors Write CommandsSet Multiple Mode Write SectorsWrite DMA Write MultipleSet Features Mode Set Feature CommandsPower Mode Commands Sleep Mode Identify Drive Initialization Commands15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Seek, Format and Diagnostic Commands Execute Drive DiagnosticFormat Track Execute S.M.A.R.T A.R.T. Command SetSupport Service and SupportService Policy No Quibble ServiceMaxFax Service Customer ServiceInternet Glossary Access TimeCylinder Zero Gigabyte GB Logical Block Addressing Read Gate Signal THIN-FILM Media