Maxtor 6800 manual = Write Cache enabled

Page 58

INTERFACE COMMANDS

WORD CONTENT DESCRIPTION

83Command sets supported. If words 82, 83 and 84 = 0000h or FFFFh command set notification not supported.

15 = shall be cleared to zero

14 = shall be set to one

13-1 = reserved

0, 1 = supports Download Microcode command

84Command set extensions supported. If words 84, 85 and 86 = 0000h or FFFFh command set notification not supported.

15 = shall be cleared to zero

14 = shall be set to one

13-0 = reserved

85Command set enabled. If words 84, 85 and 86 = 0000h or FFFFh command set notification not supported.

15, 1 = Identify Device DMA command enabled 14, 1 = NOP command enabled

13, 1 = Write Buffer command enabled 12, 1 = Read Buffer command enabled 11, 1 = Write Verify command enabled

10, 1 = Host Protected Area feature set enabled 9, 1 = Device Reset command enabled

8, 1 = Service Interrupt enabled 7, 1 = Release Interrupt enabled 6, 1 = Look Ahead enabled

5, 1 = Write Cache enabled

4, 1 = Packet command feature set enabled 3, 1 = Power Mangement feature set enabled 2, 1 = Removable feature set enabled

1, 1 = Security feature set enabled 0, 1 = SMART feature set enabled

86Command sets enabled. If words 85, 86 and 87 = 0000h or FFFFh command set notification not supported.

15 = shall be cleared to zero

14 = shall be set to one

13-1 = reserved

0, 1 = supports Download Microcode command

87Command sets enabled. If words 85, 86 and 87 = 0000h or FFFFh command set notification not supported.

15 = shall be cleared to zero

14 = shall be set to one

13-0 = reserved

88Ultra DMA

15-11 Reserved

10 1 = Ultra DMA Mode 2 is selected

9 1 = Ultra DMA Mode 1 is selected

8 1 = Ultra DMA Mode 0 is selected

7-3 Reserved

2 1 = Ultra DMA Modes 2 and below are supported

11 = Ultra DMA Modes 1 and below are supported 0 = Ultra DMA Mode1 is not supported

01 = Ultra DMA Modes 0 is supported

0 = Ultra DMA Mode 0 is not supported

127Reserved

128Security Status 15-9 Reserved

8 Security Level 0 = High, 1 = Maximum

7-5 Reserved

4 1 = Security count expired

3 1 = Security frozen

2 1 = Security locked

1 1 = Security enabled

0 1 = Security supported

129-130 Reserved

131Spin at power-up, but 0 is asserted when no spin at power-up is enabled. 132-159 Maxtor-specific (not used)

160-255 Reserved

7 – 11

Image 58

Contents HA RD Drive Produc T MA Nual DiamondMax Before You Begin U T I O NContents Product Specifications Handling and InstallationAT Interface Description Host Software InterfaceService and Support Interface CommandsGlossary Figures Manual Organization IntroductionMaxtor Corporation AbbreviationsKey Words Signal ConventionsConventions NumberingDiamondMax 6800 Key Features Product DescriptionProduct Features Functional / InterfaceDefect Management Zone DMZ On-the-Fly Hardware Error Correction Code ECCLogical Block Addressing Software ECC CorrectionBuffer Segmentation Read-Ahead ModeCache Management Automatic Write Reallocation AWRMajor HDA Components Cylinder Limitation Subsystem ConfigurationJumper Location/Configuration Dual Drive SupportPerformance Specifications Product SpecificationsDrive Configuration Models and CapacitiesPhysical Dimensions Parameter Standard MetricEPA Energy Star Compliance Power RequirementsPower Mode Definitions Environmental LimitsReliability Specifications Shock and VibrationRadiated Electromagnetic Field Emissions EMC Compliance Safety Regulatory ComplianceCanadian Emissions Statement Pre-formatted Drive Handling and InstallationHard Drive Handling Precautions Important NoticeUnpacking and Inspection Multi-pack Shipping ContainerRecommended Mounting Configuration Physical InstallationRepacking System Requirements Handling PrecautionsTools for Installation Drive Identification InformationGeneral Requirements Hard Drive IdentificationInstalling in a Device Bay Systems Using Cable SelectInstalling 5.25-inch Mounting Brackets and Rails Mounting Drive in SystemAttaching Interface and Power Cables Attaching System CablesSetting the Bios Cmos System SetupBios Cmos Parameters Hard Drive Preparation System Hangs During Boot AT Interface Description Interface ConnectorPin Description Summary PIN Name Signal Name Signal Description Pin Description TableTiming Parameters Mode PIO TimingDMA Timing Mode MIN MAX Ultra DMA TimingSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Host Software Interface Error RegisterFeatures Register Task File RegistersCylinder Number Registers Sector Count RegisterSector Number Register Device/Head RegisterCommand Register Command Name Command Code Parameters Used SDH SummaryDevice Control Register Control Diagnostic RegistersAlternate Status Register Digital Input RegisterReset Handling Reset and Interrupt HandlingInterrupt Handling Interface Commands Set Feature CommandsRead Sectors Read CommandsRead Verify Sectors Read DMA Read MultipleWrite Sectors Write CommandsSet Multiple Mode Write Verify SectorsWrite Multiple Write DMASet Feature Commands Set Features ModePower Mode Commands Sleep Mode Initialization Commands Identify Drive15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Execute Drive Diagnostic Seek, Format and Diagnostic CommandsFormat Track A.R.T. Command Set Execute S.M.A.R.TNo Quibble Service Service and SupportService Policy SupportCustomer Service MaxFax ServiceInternet Access Time GlossaryCylinder Zero Gigabyte GB Logical Block Addressing Read Gate Signal THIN-FILM Media