Maxtor 2R015H1, 2R010H1 specifications Shock and Vibration, Reliability Specifications

Page 18

PRODUCT SPECIFICATIONS

Shock and Vibration

PARAM ETER	OPER AT ING	N ON-OPER AT ING

Mechanical Shoc k	30 Gs, 2.0 ms , no errors	300	Gs, 2.0 ms , no damage

Rotational Shoc k		20,000 Rad/sec ,0.5 to 1.0 ms , no d

Random Vibration	10 to 45 Hz at 0.004 G2/Hz	PSD :
	48 to 62 Hz at 0.008 G2/Hz	10 Hz at .05 G2/Hz
	65 to 300 Hz at 0.004 G2/Hz	20 Hz at .055 G2/Hz,
	301 to 500 Hz at 0.0006 G2/Hz	300	Hz at .05 G2/Hz
	no errors	301	Hz at .0014 G2/Hz
		500	Hz at .001 G2/Hz
		760	Hz at .001 G2/Hz
		877	Hz at .003 G2/Hz
		1000 Hz at .001 G2/Hz
		1570 Hz at .001 G2/Hz
		2000 Hz at .0001 G2/Hz
Swept Sine Vibration
10 to 300 Hz	1 G (0 to peak ) amplitude, 1 octave per minute

Reliability Specifications

Annual Return Rate
< 0.5%	Annual Return Rate (ARR) indicates the average against products shipped.
	ARR includes all reasons for returns (failures, handling damage, NDF), but
	does not include inventory credit returns.
Quality Acceptance Rate
<1,000 DPPM	The quality acceptance rate indicates the percentage of Maxtor products
	successfully installed by our customers, and/or the number of defective parts
	per million (DPPM) encountered during the entire installation process.
Start/Stop Cycles
>50,000	This indicates the average minimum cycles for reliable start/stop function.
Load/Unload Cycles
>100,000	This indicates the average minimum cycles for reliable load/unload function.
Data Reliability
<1 per 10E15 bits read	Data errors (non-recoverable). Average data error rate allowed with all error
	recovery features activated.
Component Design Life
5 years (minimum)	Component design life is defined as a.) the time period before identified
	wear-out mechanisms impact the failure rate, or b.) the time period up to the
	wear-out point when useful component life expires.

3 – 4

Image 18

Contents Hard Disk Drive Specifications Models 2R015H1 & 2R010H1 Before You Begin U T I O NContents Product Specifications Handling and InstallationInterface Commands AT Interface DescriptionHost Software Interface Service and Support GlossaryFigures ManualOrganization IntroductionMaxtorCorporation AbbreviationsConventions Key Features Product DescriptionProduct Features Functional / InterfaceCacheManagement Major HDA Components SubsystemConfiguration Jumper Location / ConfigurationCylinder Limitation Jumper Description PerformanceSpecifications ProductSpecificationsDrive Configuration Models and CapacitiesPhysical Dimensions EPA Energy Star Compliance PowerRequirementsPower Mode Definitions Environmental LimitsReliability Specifications Shock and VibrationSafety Regulatory Compliance EMC/EMIHandlingandInstallation HardDriveHandlingPrecautionsElectro-StaticDischargeESD UnpackingandInspection Multi-pack Shipping ContainerPhysicalInstallation RepackingBefore You Begin Hook upSet up Start upPinDescriptionSummary InterfaceConnectorATInterfaceDescription PIN IGN ALPIN Name Signal Name Signal Desc Ription Pin Description TableIM in G Paramet ERS Mode PIO TimingImin G Paramet ERS Mode DMATimingUltra DMA Timing ModeSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst HostSoftwareInterface Task File RegistersPOR T EAD WR ITE Conten TS LBA Bits CommandRegister Seek, Format, and Diagnostic CommandsSummary M M a N D N a M E M M a N D code PA R a M E T E R S U S E DControl Diagnostic Registers Reset and Interrupt Handling InterfaceCommands ReadCommands Read DMA WriteCommands Write Multiple ModeSet/CheckCommands VAL UE DES C RIP TionLE VE L VAL UE Omman D PowerModeCommands Timer VAL UE TIME-OUT PeriodSleep Mode InitializationCommands Or D ENT Desc RiptionOr D 15- 10, as c urrently defined Initialize Drive Parameters Seek,FormatandDiagnosticCommands ER ROR Code Desc RiptionA.R.T. CommandSet Key RegisterNo Quibble Service ServiceandSupportService Policy Product SupportFrom Dial Glossary Channel Correctable errorCentral processing unit CPU CharacterError correction code ECC Direct accessDirect memory access DMA Error freeFrequency response Hard errorHead disk assembly HDA Gigabyte GBLogic Late windowLatency Logical addressRandom access memory RAM Phase locked loop PLLPhase margin Read gate signalSequential access Sector pulse signalSeek complete signal Soft errorUnrecoverable error Strobe offset signalUn-correctable error Write gate signal