Maxtor 2R015H1, 2R010H1 specifications PowerModeCommands, Timer VAL UE TIME-OUT Period

Page 48

INTERFACE COMMANDS

PowerModeCommands

Standby Immediate – 94h/E0h

Spin down and do not change time out value. This command will spin the drive down and cause the drive to enter the STANDBY MODE immediately. If the drive is already spun down, the spin down sequence is not executed.

Idle Immediate – 95h/E1h

Spin up and do not change time out value. This command will spin up the spin motor if the drive is spun down, and cause the drive to enter the IDLE MODE immediately. If the drive is already spinning, the spin up sequence is not executed. The actuator is parked and some circuits are powered off.

Standby – 96h/E2h

Spin down and change time out value. This command will spin the drive down and cause the drive to enter the STANDBY MODE immediately. If the drive is already spun down, the spin down sequence is not executed. A non-zero value placed in the sector count register will enable the Automatic Power Down sequence. The timer will begin counting down when the drive returns to the IDLE MODE. A value of zero placed in the sector count register will disable the Automatic Power Down sequence.

Idle – 97h/E3h

Spin up and change time out value. This command will spin-up the spin motor if the drive is spun-down.

If the drive is already spinning, the spin up sequence is not executed. A non-zero value placed in the Sector Count register will enable the Automatic Power Down sequence and their timer will begin counting down immediately. A value of zero placed in the Sector Count register will disable the Automatic Power Down sequence. The actuator is parked and some circuits are powered off.

TIMER VAL UE

TIME-OUT PERIOD

 

 

0

Time-out disabled

 

 

1 - 240

(value * 5) seconds

241 - 251

((value - 240) * 30) minutes

252

21 minutes

253

Vendor unique period = 10 hours

254

Reserved

255

21 m inutes, 15 seconds

Check Power Mode – 98h/E5h

This command returns a code in the Sector Count register that determines the current Power Mode status of the drive. If the drive is in, going to, or recovering from the STANDBY MODE the drive sets the Sector Count register to OOh. If the drive is in the IDLE MODE or ACTIVE MODE, the drive sets the Sector Count register to FFh.

Set Sleep Mode – 99h/E6h

This command will spin the drive down and cause the drive to enter the SLEEP MODE immediately. If the drive is already spun down, the spin down sequence is not executed.

Note: The only way to recover from SLEEP MODE is with a software reset or a hardware reset.

7 – 8

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Hard Disk Drive Specifications Models 2R015H1 & 2R010H1 Before You Begin U T I O NContents Product Specifications Handling and InstallationInterface Commands AT Interface DescriptionHost Software Interface Service and Support GlossaryFigures Introduction MaxtorCorporationManualOrganization AbbreviationsConventions Key Features Product DescriptionProduct Features Functional / InterfaceCacheManagement Major HDA Components SubsystemConfiguration Jumper Location / ConfigurationCylinder Limitation Jumper Description ProductSpecifications Drive ConfigurationPerformanceSpecifications Models and CapacitiesPhysical Dimensions PowerRequirements Power Mode DefinitionsEPA Energy Star Compliance Environmental LimitsReliability Specifications Shock and VibrationSafety Regulatory Compliance EMC/EMIHandlingandInstallation HardDriveHandlingPrecautionsElectro-StaticDischargeESD UnpackingandInspection Multi-pack Shipping ContainerPhysicalInstallation RepackingBefore You Begin Hook upSet up Start upInterfaceConnector ATInterfaceDescriptionPinDescriptionSummary PIN IGN ALPIN Name Signal Name Signal Desc Ription Pin Description TableIM in G Paramet ERS Mode PIO TimingImin G Paramet ERS Mode DMATimingUltra DMA Timing ModeSustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst HostSoftwareInterface Task File RegistersPOR T EAD WR ITE Conten TS LBA Bits CommandRegister Seek, Format, and Diagnostic CommandsSummary M M a N D N a M E M M a N D code PA R a M E T E R S U S E DControl Diagnostic Registers Reset and Interrupt Handling InterfaceCommands ReadCommands Read DMA WriteCommands Write Multiple ModeSet/CheckCommands VAL UE DES C RIP TionLE VE L VAL UE Omman D PowerModeCommands Timer VAL UE TIME-OUT PeriodSleep Mode InitializationCommands Or D ENT Desc RiptionOr D 15- 10, as c urrently defined Initialize Drive Parameters Seek,FormatandDiagnosticCommands ER ROR Code Desc RiptionA.R.T. CommandSet Key RegisterServiceandSupport Service PolicyNo Quibble Service Product SupportFrom Dial Glossary Correctable error Central processing unit CPUChannel CharacterDirect access Direct memory access DMAError correction code ECC Error freeHard error Head disk assembly HDAFrequency response Gigabyte GBLate window LatencyLogic Logical addressPhase locked loop PLL Phase marginRandom access memory RAM Read gate signalSector pulse signal Seek complete signalSequential access Soft errorStrobe offset signal Un-correctable errorUnrecoverable error Write gate signal
Top Page Image Contents