Maxtor 100462887 manual Power specifications

Page 19

2.8Power specifications

The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 4 on page 22.

2.8.1Power consumption

Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature.

• Spinup power

Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.

• Seek mode

During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does not execute a read or write operation. Servo electronics are active. Seek mode power represents the worst-case power consumption, using only random seeks with read or write latency time. This mode is not typical and is provided for worst-case information.

• Read/write power and current

Read/write power is measured with the heads on track, based on a 16-sector write followed by a 32-msec delay, then a 16-sector read followed by a 32-msec delay.

• Operating power and current

Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each 10 reads) and 20 percent drive idle mode.

• Idle mode power

Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random track location.

• Standby mode

During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/ write electronics are in power-down mode.

Table 3:

DC power requirements

 

 

 

 

 

 

 

Power dissipation (watts)

Avg (watts, 25° C)

Avg 5V typ amps

Avg 12V typ amps

 

 

 

 

 

Spinup

 

2.8 (peak)

 

 

 

 

 

Idle*

 

8.0

0.63

0.24

 

 

 

 

Idle* (with offline activity)

8.0

0.63

0.24

 

 

 

 

Operating (40% r/w, 40% seek, 20% inop.)

10.9

0.64

0.33

 

 

 

 

Seeking (random, 20% idle)

10.9

0.59

0.39

 

 

 

 

 

Standby

 

1.5

0.24

0.01

 

 

 

 

 

Sleep

 

1.4

0.24

0.01

 

 

 

 

 

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.

DiamondMax 20 Serial ATA Product Manual, Rev. A

11

Image 19
Contents Sata Page DiamondMax 20 Serial ATA Product Manual, Rev. a DiamondMax 20 Serial ATA Product Manual, Rev. a Contents DiamondMax 20 Serial ATA Product Manual, Rev. a List of Figures Page Introduction About the Serial ATA interface Specification summary tables Drive specificationsDrive specification STM3160811AS STM3160211AS Drive specifications summary for 160 Gbyte modelsYes Drive specification STM380811AS STM380211AS STM340211AS Drive specifications summary for 80 and 40 Gbyte modelsDiamondMax 20 Serial ATA Product Manual, Rev. a Cylinders Read/write heads Sectors per track 16,383 Default logical geometryLBA mode Formatted capacityRecording and interface technology Physical characteristicsStart/stop times Seek timeTypical seek times msec Read Write Power specifications Conducted noise Typical current profilesVoltage tolerance Sleep mode Power-management modesActive mode Idle modeEnvironmental specifications Nonoperating vibration AcousticsVibration Operating vibrationTest Description Performance level Reference standard Electromagnetic immunityReliability Radio frequency environmentsKorean RRL Safety certificationAgency certification Electromagnetic compatibilityFCC verification Environmental protectionEuropean Union Restriction of Hazardous Substances RoHS Corrosive environment DiamondMax 20 Serial ATA Product Manual, Rev. a Handling and static-discharge precautions Configuring and mounting the driveSerial ATA cables and connectors Configuring the driveDrive mounting Mounting dimensions-top, side and end viewDiamondMax 20 Serial ATA Product Manual, Rev. a Hot-Plug compatibility Serial ATA Sata interfacePin Function Definition Serial ATA device plug connector pin definitionsSerial ATA connector pin definitions SignalSupported ATA commands Supported ATA commandsCommand name Command code in hex F4H Word Description Value Identify Device commandXx07H Bit Word Description if bit is set to Bit WordSet Features command values Set Features commandA.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command DiamondMax 20 Serial ATA Product Manual, Rev. a Maxtor support services DiamondMax 20 Serial ATA Product Manual, Rev. a Index RRL Sata DiamondMax 20 Serial ATA Product Manual, Rev. a Page Maxtor Corporation

100462887 specifications

The Maxtor 100462887 is a noteworthy hard drive that has made its mark in the storage category, particularly for users requiring reliable and spacious data storage solutions. With a capacity of 100GB, this hard drive presents a solid option for individuals and small businesses looking to manage substantial amounts of information, from documents to multimedia files.

One of the key features of the Maxtor 100462887 is its 7200 RPM spindle speed, which allows for quick data access and transfer rates. This speed greatly enhances the overall performance of the hard drive, making it suitable for scenarios where rapid data retrieval is critical, such as gaming, video editing, and running intensive applications. Coupled with its Ultra ATA/133 interface, the drive can support high-speed data transfers, significantly improving the user experience.

The Maxtor 100462887 employs advanced data storage technologies aimed at providing users with not only speed but also reliability. One such technology is the use of an advanced caching mechanism, which allows for efficient management of frequently accessed data. This results in reduced latency and improved performance, especially when the drive is engaged with multiple read and write operations simultaneously.

In terms of physical characteristics, the Maxtor 100462887 is designed to fit seamlessly into a standard 3.5-inch drive bay, making it compatible with most desktop systems. Its robust build ensures durability, which is essential considering the critical role that hard drives play in data storage and retrieval. Additionally, this hard drive includes built-in shock protection against incidental impacts, thereby safeguarding your data from potential damage.

Energy efficiency is also a priority for the Maxtor 100462887, as it operates with a relatively low power consumption, making it an environmentally friendly choice. This efficiency not only helps conserve energy but also minimizes heat generation, leading to extended life expectancy of the drive.

Given its blend of performance, reliability, and efficiency, the Maxtor 100462887 serves as an excellent choice for users seeking a dependable hard drive that meets their data storage needs, whether for personal use, home entertainment systems, or small scale business operations.