FieldServer FS-8704-09 SNMP instruction manual State=%s

FS-8704-09 SNMP Driver Manual											Page 37 of 39
	Message					Description/Action
						and the driver requires that the parameter ‘SNMP_OID_Index2’ is
						defined. Refer to Appendix A.2
	SNMP:#43	Err		Undefined		The	driver	found	a Map Descriptor parameter heading
						‘SNMP_Trap_Store_Method’ but could not find a value for it.. Refer
	SNMP_Trap_Store_Method					to Appendix A.28
	SNMP:#44	Err		Undefined		The driver found a MD parameter heading ‘SNMP_Write_as_Trap’
						but could not find a value for it.				Refer to Appendix A.2Refer to
	SNMP_Write_as_Trap					Appendix A.28
	SNMP:#45	Err.		Undefined		The driver found a MD parameter heading ‘SNMP_Read_Method’
	SNMP_Read_Method					but could not find a value for it. Refer to Appendix A.28
	SNMP:#46	FYI.		Duplicate		Refer to Appendix A.2. When adding entries to the driver lookup
						table a duplicate lookup string was found. You probably did not
	state=<%s>					intend this. 8
	SNMP:#47 Err. No space. Driver					Refer to Appendix. You are adding entries to the driver lookup table
	rejects	value		state=<%s>		and	the driver has		run out of space.		If you need more entries
	value=%d					contact the FST sales group.
	SNMP:#48	FYI.			Added	This message is for information only. The driver prints it each time a
	state=<%s> value=%d					new entry is added to the lookup table. Refer to Appendix A.2
						Refer to Appendix A.2. The driver has been told to store data from a
	SNMP:#49 Err. Cant find lookup					trap using the lookup method. The search string was extracted from
	table entry below					the trap but a matching entry could not be found in the table. If the
						data is required, a new entry for the table will need to be created. 8
						Refer to Appendix A.2. The driver is building the search string by
	SNMP:#50 Err. Found non-string					extracting data from the trap. The search string is built by extracting
	data while extracting string					data from two OID fields which should be formatted as strings. A
						non-string has been found. To resolve this issue you will need to
						reconfigure the agent that produced the trap.
	SNMP:#51	Err	Indexed		Store.	Refer to Appendix A.2. The driver is storing data using the lookup
						method. The		offset	into the data	Array that corresponds to the
	Offset too big to store					search string points beyond the end of the Data Array. You may
	DAOffset=%d		IndexOffset=%d
						need to increase the length of the Data Array or change the offset
	Off=%d DA=%s Len=%d					value associated with the search string. 8
	SNMP:#52 FYI. Lookup=%s:%s					This message is for information only.					Each time the driver stores
						data using the lookup method this message is printed so that you
	Value=%d DA:Off=%s:%d
						can see the effect of the trap.
						You are trying to send a trap with Ascii string data but the when the
	SNMP:#53 FYI Cant send trap					Data Array was inspected for data to form the string it found a zero
	with null string. DA=%s Off=%d					in the 1st location and hence it thinks the string is empty. Make sure
						the data array has some data to form the string.
	SNMP:#54	Err.		Diagnostic		An internal diagnostic has been generated. Take a log and call Tech
	DIAG_USER_1 - Bad TRAP					Support.9
	Length
	SNMP:#55 Err. Multiple Objects					The server can respond to polls for multiple objects in one SNMP
	Rquested.					message. Re-configure your SNMP client.
						The server has received a poll for data. The polled OID corresponds
	SNMP:#56	Err.	Needs		Data	to the named Data Array. The driver can’t find the Data Array. Either
	Array with name=%s					reconfigure the remote client to poll for an appropriate point. Read
						Appendix A or correct the configuration adding the new Data Array.

9Refer to Enote 63 on the Website for more information

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 9042 Toll Free: (888) 509 1970 email: support@fieldserver.com