Abit NI8 SLI user manual Power Management Setup, Acpi Suspend Type, Resume by USB From S3

Page 53

BIOS Setup	3-23

3-6. Power Management Setup

Phoenix – AwardBIOS CMOS Setup Utility

Power Management Setup

ACPI Suspend Type	S3(Suspend-to-RAM	Item Help
X - Resume by USB From S3	Disabled
Power Button Function	Instant-Off
Wake-Up by PME# of PCI	Disabled
Resume by Ring	Disabled
Power-On by Alarm	Disabled
X - Date of Month Alarm	0
X - Time (hh:mm:ss) Alarm	0 : 0 : 0
POWER ON Function	BUTTON ONLY
X - KB Power ON Password	Enter
X - Hot Key Power ON	Ctrl-F1
Restore on AC Power Loss	Power Off

↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

ACPI Suspend Type:

This item selects the type of Suspend mode.

[S1(PowerOn-Suspend)]:Enables the Power On Suspend function.

[S3(Suspend-To-RAM)]:Enables the Suspend to RAM function.

!Resume by USB From S3:

When set to [Enabled], this item allows you to use a USB device to wake up a system that is in the S3 (STR - Suspend To RAM) state. This item can be configured only if the item “ACPI Suspend Type” is set to [S3(STR)].

NOTE: To enable this “Resume by USB From S3” function, the wake-up header of [USB-PWR1], [USB-PWR2], [USB-PWR3], [USB-PWR4] and [USB-PWR5] must be set to [Enabled] position. Please refer to the configuration of “Wake-up Header” in section 2-4, chapter 2.

Power Button Function:

This item selects the method of powering off your system:

[Delay 4 Sec.]: Pushing the power button for more than 4 seconds will power off the system. This will prevent the system from powering off in case you accidentally hit or pushed the power button.

[Instant-Off]:Pressing and then releasing the power button at once will immediately power off the system.

Wake-Up by PME# of PCI:

When set to [Enabled], access to the onboard LAN or a PCI card such as a modem or LAN card will cause the system to wake up. The PCI card must support the wake up function.

User’s Manual

Image 53

Contents NI8 SLI Series Copyright and Warranty Notice Table of Contents Appendix C Introduction Features & SpecificationsNV Firewall Layout Diagram Chapter Install The Motherboard Hardware SetupInstall CPU, Heatsink and Fan Assembly User’s Manual Method Channel a Channel B Install System MemoryDIMM1 Install two Graphics Cards with Nvidia SLI Technology Hardware Setup Chapter ATX Power Input Connectors Connectors, Headers and SwitchesFAN Power Connectors Guru Clock Connection Header Pin 1-2 shorted default Normal operationCmos Memory Clearing Header USB-PWR1 Wake-up HeaderAudioMAX Slot Pdif Connection Front Panel Audio Connection Header Internal Audio ConnectorHled Pin 1 Front Panel Switches & Indicators HeadersRST Pin 5 Spkr Pin 13, 15, 17Additional USB Port Headers Status IndicatorFloppy and IDE Disk Drive Connectors Post Code Display PCI Express x16 Slot Serial ATA ConnectorsPCI Express x1 Slots SLI Switchboard SlotNI8 SLI NI8 SLI GR Back Panel ConnectorsPress DEL to Enter Setup Bios SetupOC Guru ΜGuru UtilityMultiplier Factor CPU Operating SpeedExternal Clock MEM ClockAbit EQ Beep Control Power Cycle Statistics Click Enter key to enter its submenu# Temperature Monitoring High/Low Limit # Voltage MonitoringAll Voltages Low Limit # Fan Speed MonitoringCPU/NB/SYS/AUX/OTES FAN Speed # FanEQ Control Control Temperature High/Low Reference TemperatureCPU FanEQ Control Fan PWM Duty Cycle High/LowAUX1 FanEQ Control DC Fan Voltage High/Low NB/SYS/AUX/OTES FanEQ ControlTime hhmmss Standard Cmos FeaturesDate mmddyy Capacity IDE HDD Auto-DetectionCylinder Head# Back to Standard Cmos Features Setup Menu Thermal Management Advanced Bios Features# CPU Feature # Back to Advanced Bios Features Setup Menu Boot Up NumLock Status Boot Up Floppy SeekDelay For HDD Secs Security OptionMemory Timings Advanced Chipset FeaturesSLI Broadcast Aperture LDT Frequency# OnChip IDE Device Integrated Peripherals# RAID Config # OnChip PCI Device Sata Mode # Back to Integrated Peripherals Setup MenuOnBoard Sata Controller Onboard FDC ControllerPower Button Function Power Management SetupAcpi Suspend Type Resume by USB From S3Date of Month Alarm Power-On by AlarmTime hhmmss Alarm Power on FunctionRestore On AC Power Loss Hot Key Power onResources Controlled By PnP/PCI ConfigurationsInit Display First Maximum Payload Size IRQ ResourcesPCI/VGA Palette Snoop Load Optimized Defaults Load Fail-Safe DefaultsSet Password Save & Exit SetupAppendix A. Install nVidia nForce Chipset Driver Click Next Appendix B. Install Realtek Audio Driver No Output PDIF-In to S/PDIF-Out pass through modeOutput digital only Output digital and analogAppendix C. Install Silicon Image 3132 Sata Driver NI8-SLI Appendix C Appendix D. Install Silicon Image 3132 RAID Driver NI8-SLI Click Finish Appendix E. Install USB 2.0 Driver Appendix E Appendix F. Install uGuru Utility Appendix F Appendix G. Generate NVRaid Floppy Disk 32 bit/64 bit Appendix G Generate SIL3132Raid Floppy Disk 32 bit/64 bit NI8-SLI Appendix H Description Appendix I. Post Code DefinitionAward Post Code Definitions Screen logo E8POST.ASM starts AutoInvoke all ISA adapter ROMs AC2005 Post Code Definition Hex Description Power On SequencePower Off Sequence NI8 SLI Series Appendix J. Troubleshooting Need Assistance? Example Main instructions Contact Person # Fax Number ∗ E-mail Address Technical Support FormProduct to you first Appendix K. How to Get Technical SupportAppendix K North America Abit Computer U.S.A. Corporation South America Thank You Abit Computer Corporation