Genius Products U.S.A BEFW11S4 manual Setup Tab Basic Setup, Internet Setup

Page 16

Wireless-B Broadband Router

The Setup Tab - Basic Setup

The first screen that appears displays the Setup tab. This allows you to change the Broadband Router's general settings. Change these settings as described here and click the Save Settings button to apply your changes or Cancel Changes to cancel your changes.

Internet Setup

The Internet Setup section configures the Broadband Router to your Internet connection. Most of this information can be obtained through your ISP.

Internet Connection Type

Choose the type of Internet connection your ISP provides from the drop down menu.

DHCP. By default, the Router’s Internet Connection Type is set to Obtain an IP automatically, which should be kept only if your ISP supports DHCP or you are connecting through a dynamic IP address.

Static IP. If you are required to use a permanent IP address to connect to the Internet, select Static IP.

IP Address. This is the Router’s IP address, when seen from the Internet. Your ISP will provide you with the IP Address you need to specify here.

Subnet Mask. This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask.

Default Gateway. Your ISP will provide you with the Default Gateway Address, which is the ISP server’s IP address.

Static DNS 1-3. Your ISP will provide you with at least one DNS (Domain Name System) Server IP Address.

PPPoE. Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to enable PPPoE.

User Name and Password. Enter the User Name and Password provided by your ISP.

Connect on Demand: Max Idle Time. You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio

Chapter 5: Configuring the Wireless-B Broadband Router

Figure 5-2: Setup Tab - Basic Setup

Figure 5-3: DHCP Connection Type

Figure 5-4: Static IP Connection Type

10

The Setup Tab - Basic Setup

Image 16
Contents Wireless- B Copyright and Trademarks Word definitionTable of Contents Appendix B Wireless Security Appendix ATroubleshootingAppendix C Upgrading Firmware Appendix D Windows Help List of Figures Broadband Router’s Back Panel26 Applications and Gaming UPnP Forwarding Introduction WelcomeWhat’s in this Guide? Wireless-B Broadband Router Network Topology RoamingNetwork Layout Getting to Know the Wireless-B Broadband Router Back PanelWireless-B Front PanelConnecting the Wireless-B Broadband Router Hardware InstallationConfiguring the Wireless-B Broadband Router OverviewSetup Tab Basic Setup Internet SetupPPPoE Connection Type Optional Settings Required by some ISPs Wireless-B Broadband Router Setup Tab MAC Address Clone 10 Setup Tab MAC Address CloneSetup Tab Advanced Routing 11 Setup Tab Advanced RoutingWireless Tab Basic Wireless Settings 13 Wireless Tab Basic Wireless SettingsWireless Tab Wireless Security 14 WPA Pre-Shared Key17 Wireless Tab WEP Wireless Tab Wireless Network Access 18 Wireless Tab Wireless Network AccessWireless Tab Advanced Wireless Settings Preamble type, Long Preambledefault or Short PreambleSecurity Tab Filter 21 Security Tab FilterSecurity Tab VPN Passthrough 23 Security Tab VPN PassthroughApplications and Gaming Tab Port Range Forwarding 24 Applications and Gaming Tab Port Range ForwardingApplications and Gaming Tab Port Triggering Applications and Gaming Tab UPnP ForwardingAdministration Tab Management Applications and Gaming Tab DMZAdministration Tab Log 29 Backup & RestoreAdministration Tab Firmware Upgrade Administration Tab Factory Defaults 33 Administration Tab Factory DefaultsStatus Tab Router By the RouterStatus Tab Local Network 35 Status Tab Local NetworkCommon Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC Want to test my Internet connection Wireless-B Broadband Router TCP UDP VPN Ipsec Can’t get the Internet game, server, or application to workNeed to upgrade the firmware To start over, I need to set the Router to factory defaultFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnecting Frequently Asked Questions Power LED keeps flashingWhere is the Router installed on the network? Is IPSec Pass-Through supported by the Router?What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? What is DMZ Hosting? What are the advanced features of the Router?What is the Ieee 802.11g standard? What Ieee 802.11b features are supported?What is ad-hoc mode? What is infrastructure mode?What is roaming? What is ISM band?What is Spread Spectrum? What is DSSS? What is FHSS? And what are their differences?What is WEP? What is a MAC Address?How do I resolve issues with signal loss? Have excellent signal strength, but I cannot see my networkSecurity Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-B Broadband Router Figure C-1 Upgrade Firmware Appendix C Upgrading FirmwareAppendix D Windows Help TCP/IPWindows 98 or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure E-3 MAC Address/Physical AddressAppendix F Glossary Wireless-B Broadband Router Wireless-B Broadband Router Wireless-B Broadband Router Wireless-B Broadband Router Wireless-B Broadband Router Appendix G Specifications Appendix H Warranty Information Appendix I Regulatory Information FCC StatementWireless-B Broadband Router Appendix J Contact Information Europe Mail Address