EPoX Computer KP6-FX2 manual IDE Secondary Master PIO The default value is Auto

Page 34

KP6-FX 2

3-15

Note: If you do not use the Onboard IDE connector, then you will need set

Onboard Primary PCI IDE: Disabled and Onboard Secondary PCI IDE: Disabled from CHIPSET FEATURES SETUP UTILITY.

The Onboard PCI IDE cable should be equal to or less than

18 inches (45 cm.).

•IDE HDD Block Mode: Select Enabled only if your hard drives support block mode.

Enabled: Enabled IDE HDD Block Mode. Provides higher HDD transfer rates.

Disabled: Disable IDE HDD Block Mode.

•PCI Slot IDE 2nd Channel: The default value is Enabled.

Enabled: Enable secondary IDE port and BIOS will assign IRQ15 for this port.

Disabled: Disable secondary IDE port and IRQ15 is available for other device.

•Onboard Primary PCI IDE: The default value is Enabled.

Enabled: Enables Onboard IDE primary port.

Disabled: Disables Onboard IDE primary port.

•Onboard Secondary PCI IDE: The default value is Enabled.

Enabled: Enables Onboard IDE secondary port.

Disabled: Disables Onboard IDE secondary port.

•IDE Primary Master PIO: The default value is Auto.

Auto:BIOS will automatically detect the Onboard Primary Master PCI IDE HDD Accessing mode.

Mode 0~4: Manually set the IDE Accessing mode.

•IDE Primary Slave PIO: The default value is Auto.

Auto:BIOS will automatically detect the Onboard Primary Slave PCI IDE HDD Accessing mode.

Mode 0~4: Manually set the IDE Accessing mode.

•IDE Secondary Master PIO: The default value is Auto.

Auto:BIOS will automatically detect the Onboard Secondary Master PCI IDE HDD Accessing mode.

Mode 0~4: Manually set the IDE Accessing mode.

•IDE Secondary Slave PIO: The default value is Auto.

Auto:BIOS will automatically detect the Onboard Secondary Slave PCI IDE HDD Accessing mode.

Mode 0~4: Manually set the IDE Accessing mode.

Page 33 Page 35
Image 34
Page 33 Page 35
Contents 6 FX Internet Access Technical Support ServicesBios Upgrades Modem AccessHandling Procedures User NoticeParts Checklist Table of Contents Appendixes Pentium II Processor Overview IntroductionPentium II Processor CPU with C. Cartridge 1 S.E.C. Cartridge Overview 2 S.E.C. Cartridge TerminologyKP6-FX 2 Specification Summary of ATX chassis features KP6-FX 2 Form-Factor OverviewI/O Shield Connector Power-On/Off RemoteSystem Block Diagram Installation KP6-FX 2 LayoutKP6-FX 2 Layout Connectors and Jumpers Power Saving LED indicator LED on when system isJP5 CPU Clock Rate Select EssjConnectors I/O Connectors Memory Configurations Award Bios Setup To enter Setup ProgramStandard Cmos Setup Bios Features SetupBios Features Setup Award Bios Setup Typematic RateChars/Sec Chipset Features Setup Choose the Chipset Features Setup in the CmosDram Read/Write Burst B/E/F The default value is x2/2/3 PCI Burst Write Combine CPU-To-PCI Write Post System Bios CacheableBit I/O Recovery Time The default value is CPU-To-PCI IDE PostingPower Management Setup Power Management SetupDescription of the Green Functions HDD Standby Mode Standby Mode Suspend Mode Power Down and Resume EventsPNP/PCI Configuration PCI Configuration SetupIntegrated Peripherals Combination of PCI INT# linesIDE Secondary Master PIO The default value is Auto Award Bios Setup Load Setup Defaults Change Supervisor or User PasswordIDE HDD Auto Detection IDE HDD Auto DetectionLBA Logical Block Addressing mode Large modeHDD LOW Level Format Save & Exit SetupExit Without Saving MAP Appendix aMemory MAP Address Range Size DescriptionInterrupt MAP Time & DMA Channels MAPIRQ H/W RTC & Cmos RAM MAP RTC & CmosPOSThex Appendix BPost Codes 01-02Program some of the Chipsets value according to Setup. Early Appendix Unexpected Errors Post hex Description Load Setup Default
Top Page Image Contents