EPoX Computer KP6-FX2 manual HDD LOW Level Format, Save & Exit Setup, Exit Without Saving

Page 39

Award BIOS SETUP

3-20

Maximum HDD size:

 

 

no. Cylinder

(1024)

x

no. Head

(

32)

x

no. Sector

(

63)

x

bytes per sector

(

512)

1 GigaByte

Note: To support LBA or LARGE mode of HDDs, there must be some software involved. All the software is located in the Award HDD Service Routine (1NT 13h). It may fail to access a HDD with LBA (LARGE) mode selected if you are running under a Operating System which replaces the whole 1NT 13h.

UNIX operating systems do not support either LBA or LARGE and must utilize the Standard mode. UNIX can support drives larger than 528MB.

3-10 HDD LOW LEVEL FORMAT

Interleave:

Select the interleave number of the hard disk drive you wish to perform a low level format on. You may select from 1 to 8. Check the documentation that came with the drive for the correct interleave number, or select 0 for auto- matic detection.

Auto scan bad track:

This allows the utility to scan first then format by each track.

Start:

Press<Y>to start low level format.

3-11 SAVE & EXIT SETUP

The "SAVE & EXIT SETUP" option will bring you back to boot up proce- dure with all the changes you just recorded in the CMOS RAM.

3-12 EXIT WITHOUT SAVING

The "EXIT WITHOUT SAVING" option will bring you back to normal boot up procedure without saving any data into CMOS RAM. All old data in the CMOS will not be destroyed.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents 6 FX Modem Access Technical Support ServicesBios Upgrades Internet AccessUser Notice Handling ProceduresParts Checklist Table of Contents Appendixes Introduction Pentium II Processor OverviewPentium II Processor CPU with C. Cartridge 2 S.E.C. Cartridge Terminology 1 S.E.C. Cartridge OverviewKP6-FX 2 Specification KP6-FX 2 Form-Factor Overview Summary of ATX chassis featuresPower-On/Off Remote I/O Shield ConnectorSystem Block Diagram KP6-FX 2 Layout InstallationKP6-FX 2 Layout Power Saving LED indicator LED on when system is Connectors and JumpersCPU Clock Rate Select Essj JP5Connectors I/O Connectors Memory Configurations To enter Setup Program Award Bios SetupBios Features Setup Standard Cmos SetupBios Features Setup Award Bios Setup Typematic RateChars/Sec Choose the Chipset Features Setup in the Cmos Chipset Features SetupDram Read/Write Burst B/E/F The default value is x2/2/3 PCI Burst Write Combine CPU-To-PCI IDE Posting System Bios CacheableBit I/O Recovery Time The default value is CPU-To-PCI Write PostPower Management Setup Power Management SetupDescription of the Green Functions Power Down and Resume Events Standby ModeSuspend Mode HDD Standby ModePCI Configuration Setup PNP/PCI ConfigurationCombination of PCI INT# lines Integrated PeripheralsIDE Secondary Master PIO The default value is Auto Award Bios Setup Change Supervisor or User Password Load Setup DefaultsIDE HDD Auto Detection IDE HDD Auto DetectionLarge mode LBA Logical Block Addressing modeSave & Exit Setup HDD LOW Level FormatExit Without Saving Address Range Size Description Appendix aMemory MAP MAPTime & DMA Channels MAP Interrupt MAPIRQ H/W RTC & Cmos RTC & Cmos RAM MAP01-02 Appendix BPost Codes POSThexProgram some of the Chipsets value according to Setup. Early Appendix Unexpected Errors Post hex Description Load Setup Default

KP6-FX2 specifications

The EPOX Computer KP6-FX2 is a notable motherboard from the late 1990s that garnered attention for its performance and versatility. Designed to support the AMD K6-2 and K6-III processors, the KP6-FX2 was particularly favored by enthusiasts looking to build cost-effective systems without sacrificing capabilities.

One of the standout features of the KP6-FX2 is its socket 7 architecture, which allowed compatibility with a broad range of processors. This flexibility provided users with options to upgrade over time, making it a long-term investment for many builders. The motherboard supports front-side bus speeds of 66/100 MHz, catering to varying performance needs and ensuring that users could benefit from enhanced processing power as new chips were released.

The KP6-FX2 supports up to 768 MB of SDRAM in three DIMM slots, another significant advantage during its time. The motherboard's ability to handle substantial memory was essential for users engaged in demanding applications or multitasking environments. Furthermore, it supports both single-sided and double-sided DIMMs, allowing for even more memory configuration options.

In terms of connectivity, the EPOX KP6-FX2 features an integrated VIA VT82C686B Southbridge, which provides an array of onboard features and I/O connectivity. Users could benefit from integrated PS/2 mouse and keyboard ports, as well as parallel and serial ports, giving them ample options for connecting peripherals. The onboard IDE controller supported up to four IDE devices, accommodating hard drives and optical drives, which was crucial for building a comprehensive system.

The motherboard also included AGP 2X support, which was advantageous for gamers and graphic designers looking to utilize 3D acceleration in their applications. With a dedicated AGP slot, users could install capable graphics cards that enhanced visual performance.

In summary, the EPOX Computer KP6-FX2 is remembered for its robust feature set and adaptability during a time when the PC industry was evolving rapidly. Its compatibility with socket 7 processors, support for substantial RAM, and integrated features made it a valuable choice for both casual users and tech enthusiasts alike. As a product of its era, the KP6-FX2 laid a foundation for future developments in motherboards, paving the way for more advanced technologies.
Top Page Image Contents