Dell 2650 manual Removing and Installing the Microprocessor

Page 54

4.Pull the socket release lever upward to the fully open position (see Figure 4-28).

NOTICE: Be careful not to bend any of the pins when removing the microprocessor. Bending the pins can permanently damage the microprocessor.

5.Lift the microprocessor out of the socket and leave the release lever in the open position so that the socket is ready for the new microprocessor (see

Figure 4-28).

Figure 4-28. Removing and Installing the Microprocessor

6.Unpack the new microprocessor.

If any of the pins on the microprocessor appear bent, see "Obtaining Technical Assistance."

7.Ensure that the microprocessor socket release lever is in the fully open position.

8.Align pin 1 on the microprocessor (see Figure 4-28) with pin 1 on the microprocessor socket.

NOTE: No force is needed to install the microprocessor in the socket. When the microprocessor is aligned correctly, it should drop into the socket.

9.Install the microprocessor in the socket (see Figure 4-28).

NOTICE: Positioning the microprocessor incorrectly can permanently damage the microprocessor and the system when you turn on the system. When placing the microprocessor in the socket, be sure that all of the pins on the microprocessor go into the corresponding holes. Be careful not to bend the pins.

10.When the microprocessor is fully seated in the socket, rotate the socket release lever back down until it snaps into place, securing the microprocessor in the socket.

11.Place the new heat sink on top of the microprocessor (see Figure 4-27).

12.Orient the securing clips as shown in Figure 4-27.

Image 54
Contents Initial release 24 Apr Initial User Contact External Visual InspectionObserving the Boot Routine Internal Visual InspectionRunning the System Diagnostics Obtaining Technical AssistanceBack to Contents System-Status Indicators System Identification IndicatorsFront-Panel Indicators and Features Back-Panel Indicators and Features Component DescriptionPower-Supply Indicator Codes Power Indicator CodesPower-Button Indicator Codes Power-Button Indicator CodesHard-Drive Indicator Codes Power-Supply Indicator CodesHard-Drive Indicator Codes LCD Status Messages NIC Indicator CodesCooling Fan Indicator Codes LCD Status MessagesSystem Setup Program Line Causes Corrective Actions MessageSee Memory Modules Removing LCD Status Messages Solving Problems Described by LCD Status MessagesSystem Messages 10. System MessagesSetup Program System Beep Codes 11. System Beep CodesCode Cause Corrective Action Support.dell.com Diagnostics Messages Alert MessagesSystem Features System Board FeaturesService Features Power Protection DevicesSupported Operating Systems Technical Specifications Other Documents You May NeedPhysical PowerVideo EnvironmentalBack to Contents Jumpers-A General Explanation System Board JumpersJumpers System Board Connectors System Board Jumper SettingsJumper Setting Description Connector Description Expansion-Card Riser-Board Components and PCI BusesScsi Backplane Board Connectors Scsi Backplane Board ComponentsRecommended Tools System OrientationRemoving the Bezel BezelSystem Cover Replacing the BezelInside the System Replacing the CoverRemoving the Control-Panel Cable Cover Control-Panel Cable CoverFront-Panel I/O Board Replacing the Control-Panel Cable CoverControl Panel Replacing the Front-Panel I/O BoardRemoving the Control Panel System Fans Replacing the Control PanelRemoving a Cooling Fan System-Fan Bracket Replacing a Cooling FanRemoving the System-Fan Bracket Power Supplies Removing a Power SupplyReplacing the System-Fan Bracket Replacing a Power Supply Expansion-Card CageRemoving the Expansion-Card Cage Replacing the Expansion-Card Cage Expansion Card Installation GuidelinesExpansion Cards PCI Bus Scan OrderInstalling an Expansion Card Removing an Expansion CardExpansion-Card Riser Board Removing the Expansion-Card Riser BoardSample Memory Module Configurations Memory Upgrade KitsMemory Module Installation Guidelines Memory ModulesPerforming a Memory Upgrade Installing Memory ModulesTotal Desired Removing the CD/Diskette Drive Tray CD and Diskettes DrivesRemoving Memory Modules Replacing the CD/Diskette Drive TrayRemoving the CD and Diskette Drives From the Tray Replacing the CD and Diskette Drives on the TrayRemoving the CD/Diskette Drive Cable Replacing the CD/Diskette Drive CableScsi Configuration Information External Scsi Tape DriveHard Drives Installing a Hard Drive Removing a Hard DriveRemoving a Hard Drive From Its Carrier Installing a Hard Drive on a CarrierIntegrated RAID Controller Activating the Integrated RAID Controller20. Installing the RAID Controller Memory Module Installing a RAID Controller Card RAID Controller CardInstalling the Scsi Backplane Daughter Card Scsi Backplane Daughter CardRemoving the Scsi Backplane Daughter Card Scsi Backplane Board Removing the Scsi Backplane BoardReplacing the Scsi Backplane Board System Board Tray Removing the System Board TrayReplacing the System Board Tray System Board Tray LeversMicroprocessors Removing the System Board Tray Levers27. Removing and Installing the Heat Sink Adding or Replacing a Microprocessor28. Removing and Installing the Microprocessor System Battery Replacing the System BatterySystem Board Removing the System BoardReplacing the System Board Using the System Setup Program Entering the System Setup ProgramResponding to Error Messages System Setup Navigation KeysSystem Setup Options Main ScreenIntegrated Devices Screen Boot Sequence ScreenHard-Disk Drive Sequence Screen System Security ScreenConsole Redirection Screen Using the System Password FeatureAssigning a System Password Exit ScreenUsing Your System Password to Secure Your System Deleting or Changing an Existing System PasswordAssigning a Setup Password Using the Setup Password FeatureDisabling a Forgotten Password Operating With a Setup Password EnabledBack to Contents Back to Contents