Dell 2650 manual Setup Program

Diskette read failure	Faulty or improperly inserted	Replace the diskette.
	diskette.
Diskette subsystem reset failed	Faulty or improperly installed	Ensure that the diskette drive is properly installed. If the problem
	diskette drive.	persists, replace the diskette drive (see "CD and Diskettes Drives").
ECC memory error	Faulty or improperly installed	Ensure that the memory modules are properly installed. If the problem
	memory modules.	persists, replace the faulty memory module(s) (see "Memory Modules").
Error: Maximum PCI option ROM count	Too many expansion cards have	Disable ROM for some of the expansion cards (see "Using the System
exceeded!	ROM enabled in the System Setup	Setup Program").
	program.
Gate A20 failure	Faulty keyboard controller; faulty	Replace the system board (see "System Board").
	system board.
Hard disk controller failure	Incorrect configuration settings in	Run the System Setup program to correct the drive type (see "Using the
	System Setup program;	System Setup Program"). If the problem persists, ensure that the hard
	improperly installed hard drive, or	drives are properly installed (see "Hard Drives"). If the problem persists,
Hard disk read failure	loose interface or power cable;	replace the system board (see "System Board").
	faulty hard-drive controller
	subsystem.
I/O parity interrupt at address	Faulty or improperly installed	Ensure that the expansion cards are properly installed. If the problem
	expansion card.	persists, replace the faulty expansion card(s) (see "Expansion Cards").
Invalid configuration information -	Incorrect configuration settings in	Check the System Setup configuration settings (see "Using the System
please run SETUP program	System Setup program;	Setup Program"). Remove the NVRAM_CLR jumper (see Figure 5-2 for
	NVRAM_CLR jumper is installed;	jumper location). If the problem persists, replace the system battery
	faulty system battery.	(see "System Battery").
Invalid NVRAM configuration, resource re-	System configuration data has	Check the System Setup configuration settings (see "Using the System
allocated	been ignored.	Setup Program").
Invalid SCSI configuration	A SCSI cable is connected to the	If a cable is connected to the SCSIB backplane board connector, the
	channel B connector on the SCSI	SCSI backplane daughter card must be installed. Ensure that the
SCSI cable detected on connector SCSIB of	backplane board; SCSI backplane	backplane daughter card is properly installed (see "SCSI Backplane
	daughter card is not installed.	Daughter Card").
the SCSI backplane, daughter card not
present
Keyboard controller failure	Faulty keyboard controller; faulty	Replace the system board (see "System Board").
	system board.
Keyboard clock line failure	Loose or improperly connected	Check the keyboard cable and connector. If the problem persists, replace
	keyboard cable; faulty keyboard;	the keyboard. If the problem persists, replace the system board (see
Keyboard data line failure
	faulty keyboard controller.	"System Board").
Keyboard failure
Keyboard stuck key failure
Memory address line failure at address,	Faulty or improperly installed	Ensure that the memory modules are properly installed. If the problem
read value expecting value	memory modules.	persists, replace the faulty memory module(s) (see "Memory Modules").
Memory double word logic failure at
address, read value expecting value
Memory high address line failure at start
address to end address
Memory high data line failure at start
address to end address
Memory odd/even logic failure at start
address to end address
Memory parity failure at start address to
end address
Memory parity error at address
Memory write/read failure at address,
read value expecting value
No boot device available	Faulty or missing CD/diskette	Check the configuration settings in the System Setup program for
	drive subsystem, hard drive, or	Integrated Devices (see "Using the System Setup Program"). If booting
	hard-drive subsystem.	from a SCSI controller, ensure that the controller is properly connected.
		If the problem persists, replace the faulty drive(s) (see "CD and
		Diskettes Drives" and "Hard Drives"). If the problem persists, replace the
		system board (see "System Board").
No boot sector on hard- disk	No operating system on hard	Check the hard-drive configuration settings in the System Setup program
	drive.	(see "Using the System Setup Program").
No PXE-capable device available	<F12> pressed during POST and	Check the configuration settings in the System Setup program for the
	no PXE devices are detected.	NICs (see "Using the System Setup Program").
No timer tick interrupt	Faulty system board.	Replace the system board (see "System Board").
Not a boot diskette	No operating system on diskette.	Use a bootable diskette.
PCI BIOS failed to install	Loose cables to expansion card	Ensure that cables to expansion cards are properly connected. Ensure
	(s); faulty or improperly installed	that the expansion cards are properly installed. If the problem persists,
	expansion card.	replace the faulty expansion card(s) (see "Expansion Cards").
Plug & Play Configuration Error Embedded	Error encountered in initializing	Install the NVRAM_CLR jumper and reboot the system (see Figure 5-2 for
xxx	PCI device; faulty system board.	jumper location). If the problem persists, ensure that the expansion
		cards are properly installed. If the problem persists, replace the faulty
Plug & Play Configuration Error PCI_n	Error encountered in initializing	expansion card(s) (see "Expansion Cards"). If the problem persists,
		update the BIOS firmware. Download the latest firmware from the
	PCI adapter.
		Dell Support website at support.dell.com.
Primary backplane is not present	Faulty or improperly installed SCSI	Ensure that the SCSI backplane board is properly installed. If the
	backplane board.	problem persists, replace the backplane board (see "SCSI Backplane
		Board").