Dell 2650 manual See Memory Modules

E07FA	TEMP CPU n	Specified microprocessor is out of	Ensure that the system cooling fans are properly installed. If the problem persists,
	THERM	acceptable temperature range and is	replace the faulty fan(s) (see "System Fans"). If the problem persists, ensure that the
		operating at a reduced speed, or	microprocessor heat sinks are properly installed. If the problem persists, replace the
		frequency.	faulty microprocessor (see "Microprocessors").
E0876	POWER PS n	No power available from the specified	Ensure that the power supplies are properly installed. If the problem persists, replace
		power supply; specified power supply is	the faulty power supply(s) (see "Power Supplies").
		improperly installed or faulty.
E0880	INSUFFICIENT	Insufficient power is being supplied to the
	PS	system; power supplies are improperly
		installed, faulty, or missing.
E0CB2	MEM SPARE	Correctable errors threshold was met in a	Ensure that the memory modules are properly installed. If the problem persists,
	BANK	memory bank: errors were remapped to	replace the faulty memory module(s) (see "Memory Modules").
		the spare bank.
E0CF1	MBE DIMM	Memory modules installed in the specified	Ensure that all banks contain memory modules of the same type and size and that
	Bank n	bank are not the same type and size;	they are properly installed. If the problem persists, replace the faulty memory module
		faulty memory module(s).	(s) (see "Memory Modules").
E0CF1	POST MEM 64K	Parity failure in the first 64 KB of main	Ensure that the memory modules are properly installed. If the problem persists,
		memory.	replace the faulty memory module(s) (see "Memory Modules").
E0CF1	POST NO	Main-memory refresh verification failure.	Ensure that all banks contain memory modules of the same type and size and that
	MEMORY		they are properly installed. If the problem persists, replace the faulty memory module
			(s) (see "Memory Modules").
E0CF5	LOG DISABLE	Multiple single-bit errors on a single	Ensure that the memory modules are properly installed. If the problem persists,
	SBE	memory module.	replace the faulty memory module(s) (see "Memory Modules").
E0D76	DRIVE FAIL	Faulty or improperly installed hard drive or	Ensure that the hard drives are properly installed. If the problem persists, replace the
		RAID controller.	faulty hard drive(s) (see "Hard Drives"). If the problem persists, replace the RAID
			controller (see "Integrated RAID Controller" and "RAID Controller Card").
E0F04	POST CMOS	CMOS write/read failure; faulty system	Replace the system board (see "System Board").
		board.
E0F04	POST CPU	Microprocessor speed control sequence	Ensure that the microprocessors are properly installed. If the problem persists,
	SPEED	failure.	replace the faulty microprocessor(s) (see "Microprocessors").
E0F04	POST DMA	DMA initialization failure; DMA page	Ensure that the memory modules are properly installed. If the problem persists,
	INIT	register write/read failure.	replace the faulty memory module(s) (see "Memory Modules").
E0F04	POST DMA REG	Faulty system board.	Replace the system board (see "System Board").
E0F04	POST KYB	Faulty keyboard controller; faulty system	Replace the system board (see "System Board").
	CNTRL	board.
E0F04	POST MEM	Main-memory refresh verification failure.	Ensure that the memory modules are properly installed. If the problem persists,
	RFSH		replace the faulty memory module(s) (see "Memory Modules").
E0F04	POST PIC REG	Master or slave PIC register test failure.	Replace the system board (see "System Board").
E0F04	POST SHADOW	BIOS-shadowing failure.	Ensure that the memory modules are properly installed. If the problem persists,
			replace the faulty memory module(s) (see "Memory Modules").
E0F04	POST SHD	Shutdown test failure.
	TEST
E0F04	POST SIO	Super I/O chip failure; faulty system	Replace the system board (see "System Board").
		board.
E0F04	POST TIMER	Programmable interval timer test failure;	Replace the system board (see "System Board").
		faulty system board.
E0F0B	POST ROM	Faulty or improperly installed expansion	Ensure that the expansion cards are properly installed. If the problem persists,
	CHKSUM	card.	replace the faulty expansion card(s) (see "Expansion Cards").
E0F0C	VID MATCH	Specified microprocessor is faulty,	Ensure that the microprocessors are properly installed. If the problem persists,
	CPU n	unsupported, improperly installed, or	replace the faulty microprocessor(s) (see "Microprocessors").
		missing.
E10F3	LOG DISABLE	BIOS disabled logging errors.	Check the SEL for details on the errors.
	BIOS
E13F2	IO CHANNEL	Faulty or improperly installed expansion	Ensure that the expansion cards are properly installed. If the problem persists,
	CHECK	card; faulty system board.	replace the faulty expansion card(s) (see "Expansion Cards"). If the problem persists,
			replace the system board (see "System Board").
E13F4	PCI PARITY
E13F5	PCI SYSTEM
E13F8	CPU BUS INIT	Faulty or improperly installed	Ensure that the microprocessors are properly installed. If the problem persists,
		microprocessor or system board.	replace the faulty microprocessor(s) (see "Microprocessors"). If the problem persists,
			replace the system board (see "System Board").
E13F8	CPU BUS	Faulty system board.	Replace the system board (see "System Board").
	PARITY
E13F8	CPU MCKERR	Machine check error; faulty or improperly	Ensure that the microprocessors are properly installed. If the problem persists,
		installed microprocessor; faulty system	replace the faulty microprocessor(s) (see "Microprocessors"). If the problem persists,
		board.	replace the system board (see "System Board").
E13F8	HOST BUS	Faulty system board.	Replace the system board (see "System Board").
E13F8	HOST TO PCI
	BUS
E13F8	MEM	Faulty or improperly installed memory	Ensure that the memory modules are properly installed. If the problem persists,
	CONTROLLER	module; faulty system board.	replace the faulty memory module(s) (see "Memory Modules"). If the problem
			persists, replace the system board (see "System Board").
E1580	POWER	Faulty system board.	Replace the system board (see "System Board").
	CONTROL
E20F1	OS HANG	Operating system watchdog timer timed	Restart your system. If the problem persists, see your operating system
		out.	documentation.