Dell 2650 CD and Diskettes Drives, Removing Memory Modules, Removing the CD/Diskette Drive Tray

Page 41

5.Align the memory module's edge connector with the alignment key, and insert the memory module in the connector (see Figure 4-14).

The memory module connector has an alignment key that allows the memory module to be installed in the connector in only one way.

6.Press down on the memory module with your thumbs while pulling up on the ejectors with your index fingers to lock the memory module into the connector (see Figure 4-14).

When the memory module is properly seated in the connector, the memory module connector ejectors should align with the ejectors on the other connectors with memory modules installed.

7.Repeat steps 3 through 6 of this procedure to install the remaining memory modules.

8.Perform steps 4 through 8 of the procedure in "Performing a Memory Upgrade."

Removing Memory Modules

CAUTION: Before you perform this procedure, read the safety instructions in your System Information document.

CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.

1.Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2.Remove the cover (see "Removing the Cover").

3.Locate the memory module connectors from which you will remove memory modules (see Figure 5-3).

4.Press down and outward on the memory module connector ejectors until the memory module pops out of the connector (see Figure 4-14).

5.Repeat steps 3 and 4 of this procedure to remove any other memory modules.

6.Perform steps 4 through 8 of the procedure in "Performing a Memory Upgrade."

CD and Diskettes Drives

A CD drive and a diskette drive mount together on a tray that slides in the front panel and connects to the controllers on the system board through the SCSI backplane board.

Removing the CD/Diskette Drive Tray

CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.

1.Remove the bezel (see "Removing the Bezel").

2.Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.

3.Grasp the CD/diskette drive tray release handle and pull the tray out of the system (see Figure 4-15).

Figure 4-15. Removing and Installing the CD/Diskette Drive Tray

Replacing the CD/Diskette Drive Tray

CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.

1.Align the CD/diskette drive tray with the opening in the front panel.

Image 41
Contents Initial release 24 Apr External Visual Inspection Initial User ContactInternal Visual Inspection Observing the Boot RoutineObtaining Technical Assistance Running the System DiagnosticsBack to Contents Front-Panel Indicators and Features System-Status IndicatorsSystem Identification Indicators Component Description Back-Panel Indicators and FeaturesPower-Button Indicator Codes Power Indicator CodesPower-Supply Indicator Codes Power-Button Indicator CodesHard-Drive Indicator Codes Hard-Drive Indicator CodesPower-Supply Indicator Codes Cooling Fan Indicator Codes NIC Indicator CodesLCD Status Messages LCD Status MessagesLine Causes Corrective Actions Message System Setup ProgramSee Memory Modules System Messages Solving Problems Described by LCD Status MessagesRemoving LCD Status Messages 10. System MessagesSetup Program Code Cause Corrective Action System Beep Codes11. System Beep Codes Support.dell.com Alert Messages Diagnostics MessagesSystem Board Features System FeaturesSupported Operating Systems Service FeaturesPower Protection Devices Other Documents You May Need Technical SpecificationsVideo PowerPhysical EnvironmentalBack to Contents Jumpers Jumpers-A General ExplanationSystem Board Jumpers Jumper Setting Description System Board ConnectorsSystem Board Jumper Settings Expansion-Card Riser-Board Components and PCI Buses Connector DescriptionScsi Backplane Board Components Scsi Backplane Board ConnectorsSystem Orientation Recommended ToolsSystem Cover BezelRemoving the Bezel Replacing the BezelReplacing the Cover Inside the SystemFront-Panel I/O Board Control-Panel Cable CoverRemoving the Control-Panel Cable Cover Replacing the Control-Panel Cable CoverRemoving the Control Panel Control PanelReplacing the Front-Panel I/O Board Removing a Cooling Fan System FansReplacing the Control Panel Removing the System-Fan Bracket System-Fan BracketReplacing a Cooling Fan Replacing the System-Fan Bracket Power SuppliesRemoving a Power Supply Removing the Expansion-Card Cage Replacing a Power SupplyExpansion-Card Cage Expansion Cards Expansion Card Installation GuidelinesReplacing the Expansion-Card Cage PCI Bus Scan OrderRemoving an Expansion Card Installing an Expansion CardRemoving the Expansion-Card Riser Board Expansion-Card Riser BoardMemory Module Installation Guidelines Memory Upgrade KitsSample Memory Module Configurations Memory ModulesTotal Desired Performing a Memory UpgradeInstalling Memory Modules Removing Memory Modules CD and Diskettes DrivesRemoving the CD/Diskette Drive Tray Replacing the CD/Diskette Drive TrayReplacing the CD and Diskette Drives on the Tray Removing the CD and Diskette Drives From the TrayReplacing the CD/Diskette Drive Cable Removing the CD/Diskette Drive CableHard Drives Scsi Configuration InformationExternal Scsi Tape Drive Removing a Hard Drive Installing a Hard DriveIntegrated RAID Controller Installing a Hard Drive on a CarrierRemoving a Hard Drive From Its Carrier Activating the Integrated RAID Controller20. Installing the RAID Controller Memory Module RAID Controller Card Installing a RAID Controller CardRemoving the Scsi Backplane Daughter Card Installing the Scsi Backplane Daughter CardScsi Backplane Daughter Card Replacing the Scsi Backplane Board Scsi Backplane BoardRemoving the Scsi Backplane Board Removing the System Board Tray System Board TrayMicroprocessors System Board Tray LeversReplacing the System Board Tray Removing the System Board Tray LeversAdding or Replacing a Microprocessor 27. Removing and Installing the Heat Sink28. Removing and Installing the Microprocessor Replacing the System Battery System BatteryRemoving the System Board System BoardReplacing the System Board Responding to Error Messages Entering the System Setup ProgramUsing the System Setup Program System Setup Navigation KeysMain Screen System Setup OptionsHard-Disk Drive Sequence Screen Boot Sequence ScreenIntegrated Devices Screen System Security ScreenAssigning a System Password Using the System Password FeatureConsole Redirection Screen Exit ScreenDeleting or Changing an Existing System Password Using Your System Password to Secure Your SystemDisabling a Forgotten Password Using the Setup Password FeatureAssigning a Setup Password Operating With a Setup Password EnabledBack to Contents Back to Contents