Dell 2650 manual System Fans, Replacing the Control Panel, Removing a Cooling Fan

Page 32

Replacing the Control Panel

CAUTION: Before you perform this procedure, read the safety instructions in your System Information document.

CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.

1.Lower the control-panel assembly into the system.

2.Connect the control-panel cable to the control panel board (see Figure 4-7).

3.Align the assembly with the posts on the front panel (see Figure 4-7).

4.Replace the screws that secure the control-panel assembly in the system (see Figure 4-7).

Two screws at the top of the control-panel assembly that secures the assembly to the front panel.

One screw at the bottom of the control-panel that secures the assembly to the bottom of the chassis.

5.Replace the front-panel I/O board (see "Replacing the Front-Panel I/O Board").

6.Replace the control-panel cable cover (see "Replacing the Control-Panel Cable Cover").

System Fans

The system includes the following hot-pluggable cooling fans:

Two system fans

One expansion-card fan

One microprocessor fan for each installed microprocessor

The system may also include other optional hot-pluggable fans.

Removing a Cooling Fan

NOTE: The procedure for removing each individual fan is the same.

CAUTION: See "Protecting Against Electrostatic Discharge" in the safety instructions in your System Information document.

NOTICE: The cooling fans are hot-pluggable. To maintain proper cooling while the system is on, replace only one fan at a time.

1.Remove the cover (see "Removing the Cover").

2.Pull the fan straight up to clear the chassis (see Figure 4-8).

Figure 4-8. Removing and Installing a Cooling Fan

Image 32
Contents Initial release 24 Apr Initial User Contact External Visual InspectionObserving the Boot Routine Internal Visual InspectionRunning the System Diagnostics Obtaining Technical AssistanceBack to Contents Front-Panel Indicators and Features System-Status IndicatorsSystem Identification Indicators Back-Panel Indicators and Features Component DescriptionPower Indicator Codes Power-Button Indicator CodesPower-Supply Indicator Codes Power-Button Indicator CodesHard-Drive Indicator Codes Hard-Drive Indicator CodesPower-Supply Indicator Codes NIC Indicator Codes Cooling Fan Indicator CodesLCD Status Messages LCD Status MessagesSystem Setup Program Line Causes Corrective Actions MessageSee Memory Modules Solving Problems Described by LCD Status Messages System MessagesRemoving LCD Status Messages 10. System MessagesSetup Program Code Cause Corrective Action System Beep Codes11. System Beep Codes Support.dell.com Diagnostics Messages Alert MessagesSystem Features System Board FeaturesSupported Operating Systems Service FeaturesPower Protection Devices Technical Specifications Other Documents You May NeedPower VideoPhysical EnvironmentalBack to Contents Jumpers Jumpers-A General ExplanationSystem Board Jumpers Jumper Setting Description System Board ConnectorsSystem Board Jumper Settings Connector Description Expansion-Card Riser-Board Components and PCI BusesScsi Backplane Board Connectors Scsi Backplane Board ComponentsRecommended Tools System OrientationBezel System CoverRemoving the Bezel Replacing the BezelInside the System Replacing the CoverControl-Panel Cable Cover Front-Panel I/O BoardRemoving the Control-Panel Cable Cover Replacing the Control-Panel Cable CoverRemoving the Control Panel Control PanelReplacing the Front-Panel I/O Board Removing a Cooling Fan System FansReplacing the Control Panel Removing the System-Fan Bracket System-Fan BracketReplacing a Cooling Fan Replacing the System-Fan Bracket Power SuppliesRemoving a Power Supply Removing the Expansion-Card Cage Replacing a Power SupplyExpansion-Card Cage Expansion Card Installation Guidelines Expansion CardsReplacing the Expansion-Card Cage PCI Bus Scan OrderInstalling an Expansion Card Removing an Expansion CardExpansion-Card Riser Board Removing the Expansion-Card Riser BoardMemory Upgrade Kits Memory Module Installation GuidelinesSample Memory Module Configurations Memory ModulesTotal Desired Performing a Memory UpgradeInstalling Memory Modules CD and Diskettes Drives Removing Memory ModulesRemoving the CD/Diskette Drive Tray Replacing the CD/Diskette Drive TrayRemoving the CD and Diskette Drives From the Tray Replacing the CD and Diskette Drives on the TrayRemoving the CD/Diskette Drive Cable Replacing the CD/Diskette Drive CableHard Drives Scsi Configuration InformationExternal Scsi Tape Drive Installing a Hard Drive Removing a Hard DriveInstalling a Hard Drive on a Carrier Integrated RAID ControllerRemoving a Hard Drive From Its Carrier Activating the Integrated RAID Controller20. Installing the RAID Controller Memory Module Installing a RAID Controller Card RAID Controller CardRemoving the Scsi Backplane Daughter Card Installing the Scsi Backplane Daughter CardScsi Backplane Daughter Card Replacing the Scsi Backplane Board Scsi Backplane BoardRemoving the Scsi Backplane Board System Board Tray Removing the System Board TraySystem Board Tray Levers MicroprocessorsReplacing the System Board Tray Removing the System Board Tray Levers27. Removing and Installing the Heat Sink Adding or Replacing a Microprocessor28. Removing and Installing the Microprocessor System Battery Replacing the System BatterySystem Board Removing the System BoardReplacing the System Board Entering the System Setup Program Responding to Error MessagesUsing the System Setup Program System Setup Navigation KeysSystem Setup Options Main ScreenBoot Sequence Screen Hard-Disk Drive Sequence ScreenIntegrated Devices Screen System Security ScreenUsing the System Password Feature Assigning a System PasswordConsole Redirection Screen Exit ScreenUsing Your System Password to Secure Your System Deleting or Changing an Existing System PasswordUsing the Setup Password Feature Disabling a Forgotten PasswordAssigning a Setup Password Operating With a Setup Password EnabledBack to Contents Back to Contents