RIDGID TS2410LS Table Saw Features and Specifications

FEATURES

PRODUCT SPECIFICATIONS

Blade Diameter	10 in.
Blade Arbor	5/8 in.
Cutting Depth at 90°	3-1/8 in.
Cutting Depth at 45°	2-1/4 in.

Rating	120 V, AC Only, 60 Hz, 15 Amps
Output Speed	4,000 r/min. (RPM)

BLADE GUARD

ASSEMBLY

ANTI-KICKBACK

PAWLS

SPREADER

MITER

GAUGE

BLADE

WRENCH

BLADE AND BLADE

WRENCH STORAGE

SWITCH

ASSEMBLY

LEG STAND

SAW BLADE

BEVEL

LOCKING

LEVER

TABLE

EXTENSION

RIP FENCE

LOCKING

LEVER

FRONT RAIL

BEVEL

SCALE

GRIPS

BEVEL

INDICATOR

BLADE HEIGHT

LOCK KNOB

HEIGHT/BEVEL

ADJUSTING

HANDWHEEL

Fig. 3

Page 10

Image 10

RIDGID TS2410LS manual Features, Product Specifications

Contents

OPERATOR’S Manual Table of Contents Introduction General Safety Rules  Guard Against Electrical Shock by Prevent  Before Making a CUT, be Sure ALL Adjust Ments are Secure Specific Safety Rules Blade Coasts After Being Turned OFF Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATION Service Symbol Signal Meaning Extension Cords Speed and WiringElectrical Grounding Instructions Glossary of Terms Features Product Specifications Know Your Table SAW See Figure Switch Assembly Operating Components Loose Parts List Tools Needed Unpacking AssemblyMounting Holes See Figures 7 To Open the LEG StandRelease Lever Grips LEG Stand Center Brace Wing NUT To Store the Table SAW AccessoriesTo SECURE/LEVEL the SAW Wing To close the leg stand To Close the LEG Stand and Move the SAWSee Figures 12 To move the leg stand To align the throat plate with the saw table To Check the Throat PlateTo REMOVE/REPLACE the Throat Plate SET Screws Removing Throat Plate To Check SAW Blade Installation To Install Blade Guard Assembly Operation To Check and Align the Blade Guard AssemblyANTI-KICKBACK Pawls HEX KEY HEX Head Bolt Spreader Causes of Kickback ApplicationsBasic Operation of the Table SAW Avoiding Kickback Cutting Tips Types of CutsCross CUT HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard To USE the IND-I-CUT Disc To Change Blade DepthTo Change Blade Angle Once the Ind-I-Cut is level To USE the RIP Fence To SET the RIP Fence Indicator to the BladeTo USE the MICRO-ADJUST Wheel on the RIP Fence Back RIP Fence Stop PIN To USE the Miter GaugeTo USE the Table Extension To Unlock Right Miter Gauge Groove Combination Square Aligning Screws Heeling Paralleling the Blade to the Miter Gauge GrooveSee Figures 32 Blade TOO Close to Miter Gauge Groove See Figures 35 Switch OFF Switch onMaking a Cross CUT Cross CUT Place Hands on Workpiece Miter Gauge Lock Knob RIP CUT Making a RIP CUTMaking a Miter CUT Blade See Figures 39 HEIGHT/BEVEL Adjusting HandwheelMaking a Bevel Cross CUT Viewed from the FRONT, below the Table SAW Making a Bevel RIP CUT Making a Large Panel CUT Making a Compound Bevel Miter CUTSupports Large Panel CUT Making a NON-THROUGH CUT Making a Dado CUT Dado CUT To Replace the Blade AdjustmentsTo install a standard blade See Figures 46 If blade is square to the table To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚See Figures 48 If blade is not square to the table Screw Lock Knob Miter Gauge ROD To Adjust the Miter GaugeBlade AT 45˚ Position Flat Head Screw SET Screw See Figures 54 To Check and Adjust the Alignment RIP FenceHEX Head Bolt Adjusting NUT Locking Lever Back Rail Locking Lever Checking the Table Extension To Adjust the Bevel Locking LeverTo Adjust the Table Extension Bevel Lock NUT Front HEX Coupling Nylon SET Screw Adjustment MaintenanceGeneral Maintenance Lubrication Brush Replacement AccessoriesBrush CAP Assembly Troubleshooting See To Check and Align the Blade Guard Adjustments section See To Set the Bevel IndicatorSee To Adjust the Miter Gauge Bevel Stops at 0˚ and 45˚ SquaringPage What is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not Covered Customer Service Information Model No TS2410LS Serial No

RIDGID Explore Features and Specs of the TS2410LS Table Saw

Models: TS2410LS

FEATURES

PRODUCT SPECIFICATIONS