To Check SAW Blade Installation | RIDGID TS2410LS guide

ASSEMBLY

TO CHECK SAW BLADE INSTALLATION

See Figure 18.

CAUTION:

To work properly, the saw blade teeth must point down toward the front of the saw. Failure to heed this warning could cause damage to the saw blade, the saw, or the workpiece.

NOTE: Arbor shaft has left-hand threads.

Unplug the saw.

Remove blade wrenches from storage area by unscrewing wing nut.

Lower the saw blade and remove the throat plate.

Make sure the bevel locking lever is securely pushed to the left. Raise the saw blade to its full height by turning the height/bevel adjusting handwheel clockwise.

To loosen the blade:

Using the smaller blade wrench, place the flat open end on the flats on the arbor shaft.

Insert the closed end of the larger blade wrench over the hex nut. Holding both wrenches firmly, pull the larger wrench forward to the front of the machine.

To tighten the blade:

Using the smaller blade wrench, place the flat open end into the flats on the arbor shaft.

Insert the closed end of the larger blade wrench over the hex nut. Holding both wrenches firmly, push the larger wrench to the back of the machine. Make sure the blade nut is securely tightened. Do not overtighten.

Check all clearances for free blade rotation. Refer to To Check and Align the Blade Guard Assembly.

TO INSTALL BLADE GUARD ASSEMBLY

See Figure 19.

Proper installation of the blade guard assembly means that the saw blade and spreader are in alignment. ALWAYS align the spreader to the saw blade prior to turning on the table saw.

Unplug the saw.

Lower the blade by turning the height/bevel adjusting handwheel counterclockwise.

Fit the locator pins into the holes on the bracket located on the trunnion.

Turn the blade guard locking knob clockwise to securely attach the blade guard in place.

Check the blade guard assembly for clearances and free movement.

SMALL BLADE

WRENCH

LARGE BLADE

WRENCH

HEX

NUT

Fig. 18

LOCATOR

PINS

BLADE GUARD

ASSEMBLY

		BLADE GUARD
	TRUNNION	LOCKING KNOB
	TRUNNION
HOLES		Fig. 19

19

Image 19

RIDGID TS2410LS manual To Check SAW Blade Installation, To Install Blade Guard Assembly

Contents

OPERATOR’S Manual Introduction Table of Contents  Guard Against Electrical Shock by Prevent General Safety Rules  Before Making a CUT, be Sure ALL Adjust Ments are Secure Specific Safety Rules Blade Coasts After Being Turned OFF Specific Safety Rules Symbol Name DESIGNATION/EXPLANATION Symbols Symbol Signal Meaning Service Grounding Instructions Speed and WiringElectrical Extension Cords Glossary of Terms Product Specifications Features See Figure Know Your Table SAW Operating Components Switch Assembly Tools Needed Loose Parts List Unpacking AssemblyMounting Holes See Figures 7 To Open the LEG StandRelease Lever Grips LEG Stand Center Brace Wing To Store the Table SAW AccessoriesTo SECURE/LEVEL the SAW Wing NUT To move the leg stand To Close the LEG Stand and Move the SAWSee Figures 12 To close the leg stand SET Screws Removing Throat Plate To Check the Throat PlateTo REMOVE/REPLACE the Throat Plate To align the throat plate with the saw table To Install Blade Guard Assembly To Check SAW Blade Installation Operation To Check and Align the Blade Guard AssemblyANTI-KICKBACK Pawls HEX KEY HEX Head Bolt Spreader Avoiding Kickback ApplicationsBasic Operation of the Table SAW Causes of Kickback Cutting Tips Types of CutsCross CUT HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard Once the Ind-I-Cut is level To Change Blade DepthTo Change Blade Angle To USE the IND-I-CUT Disc Back RIP Fence To SET the RIP Fence Indicator to the BladeTo USE the MICRO-ADJUST Wheel on the RIP Fence To USE the RIP Fence To Unlock To USE the Miter GaugeTo USE the Table Extension Stop PIN Blade TOO Close to Miter Gauge Groove Heeling Paralleling the Blade to the Miter Gauge GrooveSee Figures 32 Right Miter Gauge Groove Combination Square Aligning Screws Cross CUT Place Hands on Workpiece Miter Gauge Lock Knob Switch OFF Switch onMaking a Cross CUT See Figures 35 Blade Making a RIP CUTMaking a Miter CUT RIP CUT Viewed from the FRONT, below the Table SAW HEIGHT/BEVEL Adjusting HandwheelMaking a Bevel Cross CUT See Figures 39 Making a Bevel RIP CUT Making a Large Panel CUT Making a Compound Bevel Miter CUTSupports Large Panel CUT Making a NON-THROUGH CUT Dado CUT Making a Dado CUT See Figures 46 AdjustmentsTo install a standard blade To Replace the Blade If blade is not square to the table To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚See Figures 48 If blade is square to the table Flat Head Screw SET Screw To Adjust the Miter GaugeBlade AT 45˚ Position Screw Lock Knob Miter Gauge ROD Locking Lever To Check and Adjust the Alignment RIP FenceHEX Head Bolt Adjusting NUT Locking Lever Back Rail See Figures 54 Bevel Lock NUT Front HEX Coupling To Adjust the Bevel Locking LeverTo Adjust the Table Extension Checking the Table Extension Lubrication MaintenanceGeneral Maintenance Nylon SET Screw Adjustment Brush Replacement AccessoriesBrush CAP Assembly See To Check and Align the Blade Guard Troubleshooting Bevel Stops at 0˚ and 45˚ Squaring See To Set the Bevel IndicatorSee To Adjust the Miter Gauge Adjustments sectionPage HOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service Warranty Model No TS2410LS Serial No Customer Service Information