Symbols, Symbol Name DESIGNATION/EXPLANATION | RIDGID TS2410LS

SYMBOLS

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.

SYMBOL	NAME	DESIGNATION/EXPLANATION
V	Volts	Voltage
A	Amperes	Current
Hz	Hertz	Frequency (cycles per second)
W	Watt	Power
min	Minutes	Time
	Alternating Current	Type of current
	Direct Current	Type or a characteristic of current
no	No Load Speed	Rotational speed, at no load
	Class II Construction	Double-insulated construction
.../min	Per Minute	Revolutions, strokes, surface speed, orbits etc., per minute
	Wet Conditions Alert	Do not expose to rain or use in damp locations.
	Read The Operator’s Manual	To reduce the risk of injury, user must read and understand
	Read The Operator’s Manual	operator’s manual before using this product.
		operator’s manual before using this product.
		Always wear safety goggles or safety glasses with side
	Eye Protection	shields and, as necessary, a full face shield when operating
		this product.
	Safety Alert	Precautions that involve your safety.
	No Hands Symbol	Failure to keep your hands away from the blade will result in
	No Hands Symbol	serious personal injury.
		serious personal injury.
	Pinch Warning	Always watch for movement paying extra attention to
	Pinch Warning	potential areas where pinching could occur.
		potential areas where pinching could occur.
	Hot Surface	To reduce the risk of injury or damage, avoid contact with
	Hot Surface	any hot surface.
		any hot surface.

6

Image 6

RIDGID TS2410LS manual Symbols, Symbol Name DESIGNATION/EXPLANATION

Contents

OPERATOR’S Manual Table of Contents Introduction General Safety Rules  Guard Against Electrical Shock by Prevent Specific Safety Rules  Before Making a CUT, be Sure ALL Adjust Ments are Secure Blade Coasts After Being Turned OFF Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATION Service Symbol Signal Meaning Extension Cords Speed and WiringElectrical Grounding Instructions Glossary of Terms Features Product Specifications Know Your Table SAW See Figure Switch Assembly Operating Components Loose Parts List Tools Needed Assembly UnpackingMounting Holes To Open the LEG Stand See Figures 7Release Lever Grips LEG Stand Center Brace Wing NUT To Store the Table SAW AccessoriesTo SECURE/LEVEL the SAW Wing To close the leg stand To Close the LEG Stand and Move the SAWSee Figures 12 To move the leg stand To align the throat plate with the saw table To Check the Throat PlateTo REMOVE/REPLACE the Throat Plate SET Screws Removing Throat Plate To Check SAW Blade Installation To Install Blade Guard Assembly To Check and Align the Blade Guard Assembly OperationANTI-KICKBACK Pawls HEX KEY HEX Head Bolt Spreader Causes of Kickback ApplicationsBasic Operation of the Table SAW Avoiding Kickback Types of Cuts Cutting TipsCross CUT HOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard To USE the IND-I-CUT Disc To Change Blade DepthTo Change Blade Angle Once the Ind-I-Cut is level To USE the RIP Fence To SET the RIP Fence Indicator to the BladeTo USE the MICRO-ADJUST Wheel on the RIP Fence Back RIP Fence Stop PIN To USE the Miter GaugeTo USE the Table Extension To Unlock Right Miter Gauge Groove Combination Square Aligning Screws Heeling Paralleling the Blade to the Miter Gauge GrooveSee Figures 32 Blade TOO Close to Miter Gauge Groove See Figures 35 Switch OFF Switch onMaking a Cross CUT Cross CUT Place Hands on Workpiece Miter Gauge Lock Knob RIP CUT Making a RIP CUTMaking a Miter CUT Blade See Figures 39 HEIGHT/BEVEL Adjusting HandwheelMaking a Bevel Cross CUT Viewed from the FRONT, below the Table SAW Making a Bevel RIP CUT Making a Compound Bevel Miter CUT Making a Large Panel CUTSupports Large Panel CUT Making a NON-THROUGH CUT Making a Dado CUT Dado CUT To Replace the Blade AdjustmentsTo install a standard blade See Figures 46 If blade is square to the table To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚See Figures 48 If blade is not square to the table Screw Lock Knob Miter Gauge ROD To Adjust the Miter GaugeBlade AT 45˚ Position Flat Head Screw SET Screw See Figures 54 To Check and Adjust the Alignment RIP FenceHEX Head Bolt Adjusting NUT Locking Lever Back Rail Locking Lever Checking the Table Extension To Adjust the Bevel Locking LeverTo Adjust the Table Extension Bevel Lock NUT Front HEX Coupling Nylon SET Screw Adjustment MaintenanceGeneral Maintenance Lubrication Accessories Brush ReplacementBrush CAP Assembly Troubleshooting See To Check and Align the Blade Guard Adjustments section See To Set the Bevel IndicatorSee To Adjust the Miter Gauge Bevel Stops at 0˚ and 45˚ SquaringPage What is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not Covered Customer Service Information Model No TS2410LS Serial No