Tools Needed, Loose Parts List | RIDGID TS2410LS specs

TOOLS NEEDED

The following tools (not included) are needed for assembly and adjustments:

PHILLIPS SCREWDRIVER	COMBINATION WRENCH (4)
	(3/8 in., 7/16 in., 1/2 in., 9/16 in.)

HEX KEYS (3)

(3/32 in., 5/32 in., 3/16 in.)

COMBINATION SQUARE

FRAMING SQUARE

Fig. 5

LOOSE PARTS LIST

The following items are included with your table saw:

SWITCH KEY		BLADE GUARD
	MITER GAUGE
		ASSEMBLY

RIP FENCE

Fig. 6

Page 13

Image 13

RIDGID TS2410LS manual Tools Needed, Loose Parts List

Contents

OPERATOR’S Manual Introduction Table of Contents  Guard Against Electrical Shock by Prevent General Safety Rules  Before Making a CUT, be Sure ALL Adjust Ments are Secure Specific Safety Rules Blade Coasts After Being Turned OFF Specific Safety Rules Symbol Name DESIGNATION/EXPLANATION Symbols Symbol Signal Meaning Service Electrical Speed and WiringExtension Cords Grounding Instructions Glossary of Terms Product Specifications Features See Figure Know Your Table SAW Operating Components Switch Assembly Tools Needed Loose Parts List Unpacking AssemblyMounting Holes See Figures 7 To Open the LEG StandRelease Lever Grips LEG Stand Center Brace To SECURE/LEVEL the SAW To Store the Table SAW AccessoriesWing NUT Wing See Figures 12 To Close the LEG Stand and Move the SAWTo close the leg stand To move the leg stand To REMOVE/REPLACE the Throat Plate To Check the Throat PlateTo align the throat plate with the saw table SET Screws Removing Throat Plate To Install Blade Guard Assembly To Check SAW Blade Installation Operation To Check and Align the Blade Guard AssemblyANTI-KICKBACK Pawls HEX KEY HEX Head Bolt Spreader Basic Operation of the Table SAW ApplicationsCauses of Kickback Avoiding Kickback Cutting Tips Types of CutsCross CUT HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard To Change Blade Angle To Change Blade DepthTo USE the IND-I-CUT Disc Once the Ind-I-Cut is level To USE the MICRO-ADJUST Wheel on the RIP Fence To SET the RIP Fence Indicator to the BladeTo USE the RIP Fence Back RIP Fence To USE the Table Extension To USE the Miter GaugeStop PIN To Unlock See Figures 32 Heeling Paralleling the Blade to the Miter Gauge GrooveRight Miter Gauge Groove Combination Square Aligning Screws Blade TOO Close to Miter Gauge Groove Making a Cross CUT Switch OFF Switch onSee Figures 35 Cross CUT Place Hands on Workpiece Miter Gauge Lock Knob Making a Miter CUT Making a RIP CUTRIP CUT Blade Making a Bevel Cross CUT HEIGHT/BEVEL Adjusting HandwheelSee Figures 39 Viewed from the FRONT, below the Table SAW Making a Bevel RIP CUT Making a Large Panel CUT Making a Compound Bevel Miter CUTSupports Large Panel CUT Making a NON-THROUGH CUT Dado CUT Making a Dado CUT To install a standard blade AdjustmentsTo Replace the Blade See Figures 46 See Figures 48 To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚If blade is square to the table If blade is not square to the table Blade AT 45˚ Position To Adjust the Miter GaugeScrew Lock Knob Miter Gauge ROD Flat Head Screw SET Screw HEX Head Bolt Adjusting NUT Locking Lever Back Rail To Check and Adjust the Alignment RIP FenceSee Figures 54 Locking Lever To Adjust the Table Extension To Adjust the Bevel Locking LeverChecking the Table Extension Bevel Lock NUT Front HEX Coupling General Maintenance MaintenanceNylon SET Screw Adjustment Lubrication Brush Replacement AccessoriesBrush CAP Assembly See To Check and Align the Blade Guard Troubleshooting See To Adjust the Miter Gauge See To Set the Bevel IndicatorAdjustments section Bevel Stops at 0˚ and 45˚ SquaringPage DAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not Covered Model No TS2410LS Serial No Customer Service Information