Manuals / RIDGID / Power Tools / Saw

RIDGID TS2410LS manual To SECURE/LEVEL the SAW, To Store the Table SAW Accessories, Wing NUT

Models: TS2410LS

1 46

Download 46 pages 53.62 Kb

Page 16

ASSEMBLY

TO SECURE/LEVEL THE SAW

See Figure 10.

With the leg stand open and the table saw resting on a flat, level surface, the saw should not move or rock from side to side.

If the saw rocks from side to side, the leveling feet need adjusting until the leg stand is balanced.

Loosen both the top and bottom wing nuts.

Lift the saw slightly so that you may turn the leveling foot until the leg stand no longer rocks.

•Turning clockwise will lower the foot

•Turning counterclockwise will raise the foot

TO STORE THE TABLE SAW ACCESSORIES

See Figure 11.

The table saw has two convenient storage areas specifically designed for the saw’s accessories. These accessories must be securely stored prior to closing the leg stand and moving the saw.

Always store the blade guard when making non-through cuts and/or transporting the saw. Slide blade guard in storage area. Snap bottom edge of clear basket between latches on base.

To store the rip fence, place the top edge in first and twist downward to snap into place. To remove, pull up on fence and rotate bottom away from saw.

Pull latch forward and slide miter gauge in storage area. To remove miter gauge, pull latch forward and lift straight up.

Secure blade wrenches and saw blade using extra washers provided to separate blades and prevent tooth damage.

WING NUT

WING

NUT

LEVELING

FOOT

Fig. 10

MITER	BLADE GUARD
GAUGE	ASSEMBLY

RIP FENCE

Fig. 11

16

Image 16

RIDGID TS2410LS manual To SECURE/LEVEL the SAW, To Store the Table SAW Accessories, Wing NUT, NUT Leveling Foot Miter

Contents

OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules  Guard Against Electrical Shock by Prevent Before Making a CUT, be Sure ALL Adjust Ments are Secure Specific Safety Rules Blade Coasts After Being Turned OFF Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningSpeed and Wiring ElectricalExtension Cords Grounding InstructionsGlossary of Terms Features Product SpecificationsKnow Your Table SAW See FigureSwitch Assembly Operating ComponentsLoose Parts List Tools NeededUnpacking AssemblyMounting Holes See Figures 7 To Open the LEG StandRelease Lever Grips LEG Stand Center Brace To Store the Table SAW Accessories To SECURE/LEVEL the SAWWing NUT WingTo Close the LEG Stand and Move the SAW See Figures 12To close the leg stand To move the leg standTo Check the Throat Plate To REMOVE/REPLACE the Throat PlateTo align the throat plate with the saw table SET Screws Removing Throat PlateTo Check SAW Blade Installation To Install Blade Guard AssemblyOperation To Check and Align the Blade Guard AssemblyANTI-KICKBACK Pawls HEX KEY HEX Head Bolt Spreader Applications Basic Operation of the Table SAWCauses of Kickback Avoiding KickbackCutting Tips Types of CutsCross CUT HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard To Change Blade Depth To Change Blade AngleTo USE the IND-I-CUT Disc Once the Ind-I-Cut is levelTo SET the RIP Fence Indicator to the Blade To USE the MICRO-ADJUST Wheel on the RIP FenceTo USE the RIP Fence Back RIP FenceTo USE the Miter Gauge To USE the Table ExtensionStop PIN To UnlockHeeling Paralleling the Blade to the Miter Gauge Groove See Figures 32Right Miter Gauge Groove Combination Square Aligning Screws Blade TOO Close to Miter Gauge GrooveSwitch OFF Switch on Making a Cross CUTSee Figures 35 Cross CUT Place Hands on Workpiece Miter Gauge Lock KnobMaking a RIP CUT Making a Miter CUTRIP CUT BladeHEIGHT/BEVEL Adjusting Handwheel Making a Bevel Cross CUTSee Figures 39 Viewed from the FRONT, below the Table SAWMaking a Bevel RIP CUT Making a Large Panel CUT Making a Compound Bevel Miter CUTSupports Large Panel CUT Making a NON-THROUGH CUT Making a Dado CUT Dado CUTAdjustments To install a standard bladeTo Replace the Blade See Figures 46To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚ See Figures 48If blade is square to the table If blade is not square to the tableTo Adjust the Miter Gauge Blade AT 45˚ PositionScrew Lock Knob Miter Gauge ROD Flat Head Screw SET ScrewTo Check and Adjust the Alignment RIP Fence HEX Head Bolt Adjusting NUT Locking Lever Back RailSee Figures 54 Locking LeverTo Adjust the Bevel Locking Lever To Adjust the Table ExtensionChecking the Table Extension Bevel Lock NUT Front HEX CouplingMaintenance General MaintenanceNylon SET Screw Adjustment LubricationBrush Replacement AccessoriesBrush CAP Assembly Troubleshooting See To Check and Align the Blade GuardSee To Set the Bevel Indicator See To Adjust the Miter GaugeAdjustments section Bevel Stops at 0˚ and 45˚ SquaringPage Warranty DAY Satisfaction Guarantee PolicyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredCustomer Service Information Model No TS2410LS Serial No