Atlas Sound XLTE 6.4.2BIAMP Mode Wiring See FIGURE, Wiring for BIAMP Mode Full-Range

Page 25

6.4.2BIAMP Mode Wiring (See FIGURE 5)

6.4.2BIAMP Mode Wiring (See FIGURE 5)

Installing and operating loudspeakers in BIAMP mode requires putting the slide switch on the input panel in the BIAMP (up) position. In this mode the LF and HF connections must be made using either of the Neutrik Speakon jacks. Note that each Speakon jack can accept both the LF and HF inputs. The 1/4 in. jacks are not used for BIAMP mode. Observe proper polarity when making the connections.

FIGURE 5: Wiring for BIAMP Mode Full-Range

6.4.3Subwoofers (See FIGURE 6)

The wiring connections for the subwoofers are the same whether it is used in a stand-alone fashion or configured with a full-range loudspeaker that is used in either PASSIVE or BIAMP mode. Observe that when the FULL-RANGE OUTPUT on the subwoofer is used with a full-range loudspeaker in BIAMP mode, the subwoofer FULL-RANGE OUTPUT is connected to the LF input on the full-range loudspeaker. For convenience, the 1/4 in. jack may be used for this connection. (See “Technical Note” in SECTION 6.2.2). Observe proper polarity when making connections.

FIGURE 6: Wiring for Subwoofer

PAGE 23 Community XLT / XLTE Series Owner’s Manual

Image 25

Contents FULL-RANGESYSTEMS AND SUBWOOFERS XLT / XLTEPage COMMUNITY PROFESSIONAL LOUDSPEAKERS DIN EN 55013 08-1991 DIN EN EC STATEMENT OF CONFORMITYDIN EN Community Light & Sound, Inc. 333 East 5th StreetDIAGRAMS and TABLES TABLE OF CONTENTSCHAPTER PAGE1 INTRODUCTION 1.3IMPORTANT SAFETY INFORMATION1.2MODEL NUMBER USAGE IN THIS MANUAL 2 UNPACKING AND INSPECTION Page Page Figure 1 Physical Features 3.1FEATURES MATRIX 3 PHYSICAL FEATURES See FIGURETable 1 Physical Features Matrix 3.2FEATURES DESCRIPTIONSPhillips pan-head screws Footnotes for Physical FeaturesTable 2 Product Listing 4.3DRIVERS 4.1ABBREVIATED OPERATING INSTRUCTIONS4.3.1High Frequency Driver 4.3.2Mid Frequency Driver 46 models only4.6.2HF-LevelSwitch 4.6.1PASSIVE / BIAMP Switch4.3.4Ferrofluid Cooling 4.4PATTERN CONTROL HORNS4.6.5PowerSense Indicators 4.6.4PowerSense DDP Circuit4.7POWER HANDLING 4.6.3Subwoofer Full-RangeOutput4.8.2Corner Protectors and Stacking XLT only 4.8.1Permanent Mounting4.8.3Feet XLTE only 4.8.4Carrying Handles4.9.1Community Accessories 4.9OPTIONAL ACCESSORIES4.9.23rd Party Accessories 4.8.641 Positioning and Horn Rotation5.1CHOOSING A POWER AMPLIFIER 5 SETUP AND OPERATION5.1.2Power Amplifier Load Impedance Table 5 Recommended Amplifier Power for Subwoofer FIGURE 2 PASSIVE Mode Configurations FIGURE 3 BIAMP Mode Configurations 6.1.1Loudspeaker Wire Gauge 6 ELECTRICAL INSTALLATIONTable 6 Loudspeaker Wire Gauge Selection 6.1LOUDSPEAKER CABLE6.3.1Parallel Connector Wiring 6.2.2Internal Input Jack Wiring6.3.2Load Impedance When Paralleling Loudspeakers 6.2.1Choosing an Input Jack6.4.1PASSIVE Mode Wiring See FIGURE 6.4CONNECTING THE LOUDSPEAKERSFIGURE 4: Wiring for PASSIVE Mode Full-Range FIGURE 5 Wiring for BIAMP Mode Full-Range 6.4.2BIAMP Mode Wiring See FIGUREFIGURE 6 Wiring for Subwoofer 6.4.3Subwoofers See FIGURE7.1.1Removing and Re-installingthe Grille 7 PHYSICAL INSTALLATION7.1FRONT GRILLE 7.1.2Custom Grille Cloth7.3.2Model 42 and 7.3.1Model 41 Horn Orientation7.4MOUNTING AND RIGGING IMPORTANT NOTE Mounting/Rigging Point HolesFIGURE 7 Mounting Point Detail - Pull Direction 7.4.2Using the Community CSSUPKIT Suspension KitFIGURE 8 XLT Mounting Points DANGER7.4.4Stand Bracket Inserts 46 and 48 only 7.4.3Using the Community WB1 Mounting AccessoryDANGER See FIGURE FIGURE 9 XLTE Mounting / Rigging PointsFIGURE 10 XLTE Mounting / Rigging Point Detail 7.5.1Using the Community EYBLTKIT7.6STACKING ENCLOSURES 8.1INITIAL TESTING 8 ACOUSTICAL ADJUSTMENTS8.2FINAL ADJUSTMENTS 8.2.1Electronic Gain Structure8.2.2Residual Noise 8.2.3Volume Level Balancing8.3EQUALIZATION 8.3.1HF-LevelSwitch8.3.2Equalization Tips 8.4FINAL RESULTS9.1POWERSENSE DDP 9 OPERATING PRECAUTIONS9.1.1Operating Modes and PowerSense DDP 9.1.2PowerSense DDP Circuit OperationFIGURE 11 Amplifier Clipping 9.3ACOUSTIC VOLUME LEVEL PRECAUTIONSFIGURE 12 Sound Exposure Limits 9.4TESTING AND TEST SIGNALS10 SERVICING THE LOUDSPEAKER 10.1ACCESSING THE DRIVERS10.1.1LF Drivers 10.1.2MF and HF Drivers11.1FULL-RANGEMODELS 11 TECHNICAL SPECIFICATIONS11.2MONITOR SPEAKERS AND SUBWOOFERS 12 IN CASE OF DIFFICULTY No bass No high frequencies Transferable Limited Warranty 13WARRANTY INFORMATION AND SERVICE9907007F C. Specifications Table 8 Additional Model SpecificationsAPPENDIX - XLT41E and XLT48E A. XLT41E and XLT48E Additional ModelsINDEX Page Page Page Page Page Phone 610 876-3400Fax 333 East 5th Street, Chester, PA1999 Community Light & Sound, Inc. 991015Cm