Cobalt Networks 8321(-C), 8310(-C) user manual Remote Control Networking Features, Ethernet Setup

Page 31

Remote Control Networking Features

This section includes instructions for installing the MFC-8310-N controller card for the CFM-8310 module.

Note: Refer to Cobalt® reference guide COMPASS™ Remote Control User Guide”

(PN 9000RCS-RM) for thorough information and step-by-step instructions for setting up network remote control of COMPASS™ cards using DashBoard™ and the Network Controller Card. This guide provides information for setting up remote control using either the MFC-8310-N or MFC-8320- N Network Controller Cards.

Installing the Network Controller Card

Perform the physical installation of the MFC-8310-N controller card for the CFM-8310 using the steps provided in the section “Installing the Controller Card” of this manual. Once the controller card is installed, you can proceed to the section below to set up the Ethernet connection for your card.

Ethernet Setup

Use the following procedure to set up the Ethernet connection for the MFC-8310-N controller card:

1.On the MFC-8310-N card, set DIP_8 to ON. Refer to Figures 13 and 14 for DIP Switch locations.

2.Power up the MFC-8310-N card. The IP address of the MFC-8310-N card is set to 192.168.1.1 by default.

3.Set the IP Address of your PC to 192.168.1.x, where x is a value other than 1. Consult your IT Department for details.

4.Point your Web browser to 192.168.1.1, the IP Address of the MFC-8310-N card.

5.Set the following parameters as required:

Frame Name – This name identifies the frame.

DHCP – Set this parameter to Yes if the frame IP Address is to be set automatically.

IP Address – This is the IP Address, which is supplied by your IT Department, of the card.

NetMask – This is the subnet mask for your LAN as supplied by your IT Department.

Gateway – This is the IP Address for connection outside the subnet.

Time Server – This is the IP Address of the NTP server used as a time source.

Save Changes – Select this button to send your changes to the MFC-8310-N card. The IP Address of the card is updated.

6.Power down the MFC-8310-N card.

7.On the MFC-8310-N card, set the DIP_8 to OFF.

8.Power up the MFC-8310-N. The card will use the configured IP Address.

9.Verify the configured IP Address of the MFC-8310-N card by pointing your Web browser to the new address.

8310/8321 User Manual (V 1.0)

Page 31

Image 31
Contents Cobalt Digital Inc OpenGearTM 2RU Frame Power Supply PS-8300Trademarks CopyrightSymbol Meanings Important Regulatory and Safety NoticesImportant Safety Instructions EMC Notices Product Power Cord RequirementsUS FCC Part Environmental Information Maintenance/User Serviceable PartsContents Ordering Information Service InformationContact Us Overview IntroductionThis Chapter Word of ThanksRobust Power Supplies FeaturesDocumentation Terms Static Discharge Installation and SetupUnpacking Hazardous Voltages Installing the FramePower Supply PS-8300 and Power Cable Installing the Frame Power SupplyColor Display and Description Fault ReportingImproving Performance Ventilation and CoolingWithout Fan Kit Fan Kit InstalledPower Cable Connection Cable ConnectionsBNC Rear I/O Module Rear I/O ModulesSmpte Alarm Connector Rear I/O Module InstallationEthernet Connector OpenBUS ConnectorDual Reference Connectors Smpte 269M Fault Reporting Option Details Frame ConnectionsTechnical Specifications SpecificationsReporting Smpte FaultEnvironmental Important Notes Frame Features Installing the Cooling Fan Module Cooling FeaturesFan Board Installation Instructions Cooling Fan Functions and User Controls Frame Door FeaturesFunctions of the Controller Card Installing the Controller CardMFC-8310 LEDs MFC-8310 Alarm Configuration JumperAlarm Mute Button Controls and LEDs for the Controller CardMFC-8310 Controller Card LED Descriptions Installing the Network Controller Card Remote Control Networking FeaturesEthernet Setup Controls and LEDs for the Network Controller Card Functions of the Network Controller CardButtons on the MFC-8310-N DIP Switches on the MFC-8310-NMFC-8310-N LEDs Reset ButtonSnmp Monitoring and Control DashBoard and DashBoard Lite Control System SoftwareColor Location Display and Description Enabling Snmp Configuring SnmpOperating Tip Rear Support Bars and Brackets Installing the Rear Support Bars and Brackets8321 20-Slot Frame Setup Rear Modules for the 8321 Series Frames Split Rear Module Cooling Features Specifications for the 8321 Series Frames Troubleshooting Checklist Service InformationFrame Controller Alarm Mute/Bootload Button Page Cobalt Digital Inc. Limited Warranty Warranty and Repair PolicyStandard Equipment Ordering InformationOptional Equipment Page Contact Cobalt Digital Inc Contact UsVisit us at the Cobalt Digital Inc. website

8321(-C), 8310(-C) specifications

Cobalt Networks was known for its pioneering role in the development of high-performance server appliances, particularly with its 8300 series, which includes the 8310(-C) and 8321(-C) models. These devices are recognized for their reliability, scalability, and efficiency, making them ideal solutions for web hosting, content delivery, and database management.

The Cobalt 8310(-C) model primarily targets small to medium-sized businesses looking for a cost-effective yet powerful server solution. It features a robust hardware design, powered by a dedicated processor that ensures speedy performance and low latency for applications. With its capacity to handle multiple simultaneous connections, the 8310(-C) is well-suited for web applications and e-commerce platforms. Its compact form factor allows for easy installation in server racks, contributing to efficient space utilization in data centers.

On the other hand, the Cobalt 8321(-C) is designed for larger enterprises requiring enhanced performance and greater scalability. This model includes a multicore processor and offers higher RAM and storage options, allowing businesses to support more demanding applications and larger databases. The 8321(-C) is particularly beneficial for organizations that anticipate growth, as it can be easily scaled up with additional resources, ensuring that service quality remains consistent even during peak loads.

Both models share several key features that underscore Cobalt Networks' commitment to performance and reliability. They incorporate advanced cooling technologies to maintain optimal operating temperatures, prolonging hardware lifespan and enhancing reliability. Additionally, both models support a variety of operating systems and virtualization technologies, providing the flexibility needed to run diverse applications.

Security is another critical characteristic of the 8310(-C) and 8321(-C). They come equipped with robust security protocols, including firewall and intrusion detection systems, ensuring that sensitive data is protected from unauthorized access and cyber threats.

In summary, the Cobalt Networks 8310(-C) and 8321(-C) models stand out due to their performance, scalability, and security features. These servers are suited for businesses of varying sizes, supporting a range of applications while ensuring reliability and efficiency in demanding environments. As organizations continue to embrace digital transformation, these models remain relevant due to their robust technologies and capabilities.