Albatron Technology PX845PEV-800 Onboard FDC Controller, Onboard Serial Port, Uart Mode Select

Page 36

Albatron Anniversary Special Edition PX845PEV-800

Onboard FDC Controller

Select “Enabled” if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install an add-in FDC or the system has no floppy drive, select “Disabled”. Options: Enabled (default), Disabled.

Onboard Serial Port 1

Select an address and corresponding interrupt for the first serial port. Options: Disabled, 3F8/IRQ4 (default), 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Auto.

Onboard Serial Port 2

Select an address and corresponding interrupt for the second serial port. Options: Disabled, 2F8/IRQ3 (default), 3F8/IRQ4, 3E8/IRQ4, 2E8/IRQ3, Auto.

UART Mode Select

This item allows you to select the Infra Red (IR) standard to be used. Options: Normal (default), AS KIR, IrDA.

RxD, TxD Active

This item determines the RxD and TxD frequencies. Options: Hi / Lo (default), Hi / Hi, Lo / Hi, Lo / Lo.

IR Transmission Delay

This item allows you to enable/disable IR transmission delay. Options: Enabled (default), Disabled.

UR2 Duplex Mode

Select the transmission mode used by the IR interface. Full-duplex mode permits simultaneous bi-directional transmission. Half-duplex mode permits transmission in only one direction at a time. Options: Half (default), Full.

Use IR Pins

Consult your IR peripheral documentation to select the correct setting of the TxD and RxD signals. Options: Full, Half (default).

Onboard Parallel Port

Select an address and corresponding interrupt for the onboard parallel port. Options: 378/IRQ7 (default), 278/IRQ5, 3BC/IRQ7, Disabled.

Parallel Port Mode

This option allows you to select an parallel port mode for the on board parallel port.

ECP (default)	Extended Capabilities Port.
EPP	Enhanced Parallel Port.
SPP	Standard Printer Port.
ECP+EPP	ECP & EPP mode.
Normal

EPP Mode Select

Select EPP port type 1.7 or 1.9. Options: EPP 1.9(default), EPP 1.7.

ECP Mode Use DMA

Select a DMA Channel for the parallel port during ECP mode. Options: 3 (default), 1.

33

Image 36

Contents Albatron PX845PEV-800 Copyright Contents Getting Started IntroductionSpecifications CPULAN Bios Quick Content Table Function Content LocationConfiguration Hardware Installation SubjectCPU Processor Installation CPU Socket 478 Configuration StepsFrequency / Voltage Control FAN HeadersWatch Dog Timer FormulasMemory Installation RAM Module InstallationMemory installation note DIMM1 DIMM2 DIMM3Back Panel Configuration PS/2 Mouse & PS/2 Keyboard Connectors KB/MSUSB & LAN Connectors USB/LAN Serial and Parallel Interface Ports Serial Interface COM1/ COM2Parallel Interface Port PRT Connector Configuration Front Panel Indicator SW/LEDSpeaker Speaker Connector IrDA Infrared ConnectorFloppy Disk Connector FDC Hard Disk Connectors IDE1/ IDE2IDE1 Primary IDE Connector IDE2 Secondary IDE ConnectorCase Open Warning connector Case Open Headers & JumpersFront USB Headers USB2 / USB3 USB Bracket 2 Ports or 4 PortsClear Cmos Jumper JP1 JP1Slots AGP Accelerated Graphics Port SlotPCI Peripheral Component Interconnect Slots Power Supply Attachments ATX Power Connector ATX12V & AtxpwrBios Setup Supported CPUs Key FunctionMain Menu Main Menu Setup Configuration Options Advanced Bios Features First /Second/Third/ Boot DeviceBoot Other Device Boot Up Floppy SeekQuick Power On Self Test Boot Up NumLock StatusTypematic Rate Setting Typematic Delay MsecAdvanced Chipset Features PnP/PCI Configurations Frequency/Voltage Control Integrated Peripherals Intel OnChip IDE DeviceOn-Chip Primary/Secondary PCI IDE IDE Primary/Secondary/Master/Slave PIOOnboard I/O Chip Setup Intel OnChip PCI DeviceInit Display First Uart Mode Select IR Transmission DelayUR2 Duplex Mode Use IR PinsPower Management Run Vgabios if S3 ResumePower Management Acpi Suspend TypeSuspend Mode HDD Power DownVideo Off Method Video Off In SuspendDate of Month Alarm Time hh mm ss AlarmReload Global Timer Events USB KB Wake-up From S3Hardware Monitor Case Open WarningLoad Defaults Load System Default SettingsLoad System Turbo Settings Load Cmos From BiosSave & Exit Setup Exit MenuExit Without Saving Software Setup Software InstallationSoftware List Troubleshooting ProblemProblem Problem Specification Hardward installationSoftware Installation Appendix I：Appendix II： Appendix III： Albatron USA Inc