Albatron Technology PX845PEV-800 manual Intel OnChip PCI Device, Init Display First

Page 35

Albatron Anniversary Special Edition PX845PEV-800

IDE HDD Block Mode

Block mode is otherwise known as block transfer, multiple commands, or multiple sector read/write. Select the “Enabled” option if your IDE hard drive supports block mode (most new drives do). The system will automatically determine the optimal number of blocks to read and write per sector. Options: Enabled (default), Disabled.

INTEL OnChip PCI Device

If you highlight the “INTEL OnChip PCI Device” label and then press the enter key, it will take you a submenu with the following options:

USB Controller

This option should be enabled if your system has a USB port installed on the system board. You will need to disable this feature if you add a higher performance controller. Options: Enabled (default), Disabled.

USB 2.0 Controller

This option should be enabled if your system has a USB 2.0 device installed on the system board. You will need to disable this feature if you install a USB 1.1 device. Options: Enabled (default), Disabled.

USB Keyboard Support

Enables support for USB attached keyboards. Options: Disabled (default), Enabled.

Onboard LAN Device

This option allows you to control the onboard LAN Device. Options: Enabled (default), Disabled.

Init Display First

With systems that have multiple video cards, this option determines whether the primary display uses a PCI slot or an AGP slot. Options: AGP (default), PCI Slot.

Onboard I/O Chip Setup

If you highlight the “Onboard I/O Chip Setup” label and then press the enter key, it will take you to a submenu with the following options:

PWRON After PWR-Fail

This field will determine whether your system will boot after restoring power after a power failure. If you select “On”, the system will boot whether or not the system was on before power failure. If you select “Former-Sts”, the system will be restored to the status before the power failure. Options: Off (default),On, Former-Sts.

Power On Function

This option allows you to select a way to power on your computer.

Options: Password, Hot KEY, Mouse Left, Mouse Right, Any KEY, BUTTON ONLY (default), and Keyboard 98.

KB Power On Password

Supply a password that your system will use as part of the power-on sequence.

Hot Key Power ON

This option allows you to use the Ctrl key along with a hot key (function key) to power on your system. Options: Ctrl-F1, Ctrl-F2, …, Ctrl-F12.

32

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Albatron PX845PEV-800 Copyright Contents Introduction Getting StartedCPU SpecificationsLAN Bios Function Content Location Quick Content TableConfiguration Subject Hardware InstallationCPU Socket 478 Configuration Steps CPU Processor InstallationFAN Headers Frequency / Voltage ControlFormulas Watch Dog TimerRAM Module Installation Memory InstallationDIMM1 DIMM2 DIMM3 Memory installation noteUSB & LAN Connectors USB/LAN Back Panel ConfigurationPS/2 Mouse & PS/2 Keyboard Connectors KB/MS Parallel Interface Port PRT Serial and Parallel Interface PortsSerial Interface COM1/ COM2 Front Panel Indicator SW/LED Connector ConfigurationIrDA Infrared Connector Speaker Speaker ConnectorIDE2 Secondary IDE Connector Floppy Disk Connector FDCHard Disk Connectors IDE1/ IDE2 IDE1 Primary IDE ConnectorUSB Bracket 2 Ports or 4 Ports Case Open Warning connector Case OpenHeaders & Jumpers Front USB Headers USB2 / USB3JP1 Clear Cmos Jumper JP1PCI Peripheral Component Interconnect Slots SlotsAGP Accelerated Graphics Port Slot ATX Power Connector ATX12V & Atxpwr Power Supply AttachmentsBios Setup Key Function Supported CPUsMain Menu Main Menu Setup Configuration Options Boot Up Floppy Seek Advanced Bios FeaturesFirst /Second/Third/ Boot Device Boot Other DeviceTypematic Delay Msec Quick Power On Self TestBoot Up NumLock Status Typematic Rate SettingAdvanced Chipset Features PnP/PCI Configurations Frequency/Voltage Control IDE Primary/Secondary/Master/Slave PIO Integrated PeripheralsIntel OnChip IDE Device On-Chip Primary/Secondary PCI IDEInit Display First Onboard I/O Chip SetupIntel OnChip PCI Device Use IR Pins Uart Mode SelectIR Transmission Delay UR2 Duplex ModeAcpi Suspend Type Power ManagementRun Vgabios if S3 Resume Power ManagementVideo Off In Suspend Suspend ModeHDD Power Down Video Off MethodUSB KB Wake-up From S3 Date of Month AlarmTime hh mm ss Alarm Reload Global Timer EventsCase Open Warning Hardware MonitorLoad Cmos From Bios Load DefaultsLoad System Default Settings Load System Turbo SettingsExit Without Saving Save & Exit SetupExit Menu Software List Software SetupSoftware Installation Problem TroubleshootingProblem Problem Appendix I： SpecificationHardward installation Software InstallationAppendix II： Albatron USA Inc Appendix III：
Top Page Image Contents