Albatron Technology PX845PEV-800 manual Floppy Disk Connector FDC, Hard Disk Connectors IDE1/ IDE2

Page 20

Albatron Anniversary Special Edition PX845PEV-800

Floppy Disk Connector: FDC

This mainboard provides a standard floppy disk connector (FDC) that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy diskettes. This connector supports the floppy drive ribbon cables provided in the packaging.

Hard Disk Connectors: IDE1/ IDE2

This mainboard has a 32-bit Enhanced PCI IDE Controller that supports PIO Mode 0~4, Bus Master, Ultra DMA / 33, Ultra DMA / 66,and Ultra DMA / 100. It has two HDD connectors, IDE1 (primary) and IDE2 (secondary).

IDE1 (Primary IDE Connector)

You can connect up to two hard drives to IDE1. If you attach two drives, you must use a ribbon cable with three connectors. You must also configure one drive as the master and one drive as the slave, using the jumpers located on each drive.

IDE2 (Secondary IDE Connector)

The IDE2 controller can also support a Master and a Slave drive. The configuration is similar to IDE1. The second drive on this controller must be set to slave mode.

FDC

PhoenixPCI5

Bios

	IrDA
	FDC
	USB2
	USB3		CHASFAN
SW/LED	SPEAKER	CASE OPEN	CHASFAN	JP1

	LAN CHIP					PRT/COM		KB/MS
PCI4	PCI3	PCI2	PCI1	Winbond W83627H F	ATX	PRT/COM	USB/LAN	KB/MS
					12V

AGP

AUXFAN

82845PE

Intel

U10

So cket 478

U6

Intel 82801DB	U17	BAT1						CPUFAN

DIMM1

DIMM2

DIMM3

	IDE2	ATX_PWR
	IDE1	ATX_PWR
	IDE1

IDE2

IDE1

17

Image 20

Contents Albatron PX845PEV-800 Copyright Contents Getting Started IntroductionSpecifications CPULAN Bios Quick Content Table Function Content LocationConfiguration Hardware Installation SubjectCPU Processor Installation CPU Socket 478 Configuration StepsFrequency / Voltage Control FAN HeadersWatch Dog Timer FormulasMemory Installation RAM Module InstallationMemory installation note DIMM1 DIMM2 DIMM3USB & LAN Connectors USB/LAN Back Panel ConfigurationPS/2 Mouse & PS/2 Keyboard Connectors KB/MS Parallel Interface Port PRT Serial and Parallel Interface PortsSerial Interface COM1/ COM2 Connector Configuration Front Panel Indicator SW/LEDSpeaker Speaker Connector IrDA Infrared ConnectorFloppy Disk Connector FDC Hard Disk Connectors IDE1/ IDE2IDE1 Primary IDE Connector IDE2 Secondary IDE ConnectorCase Open Warning connector Case Open Headers & JumpersFront USB Headers USB2 / USB3 USB Bracket 2 Ports or 4 PortsClear Cmos Jumper JP1 JP1PCI Peripheral Component Interconnect Slots SlotsAGP Accelerated Graphics Port Slot Power Supply Attachments ATX Power Connector ATX12V & AtxpwrBios Setup Supported CPUs Key FunctionMain Menu Main Menu Setup Configuration Options Advanced Bios Features First /Second/Third/ Boot DeviceBoot Other Device Boot Up Floppy SeekQuick Power On Self Test Boot Up NumLock StatusTypematic Rate Setting Typematic Delay MsecAdvanced Chipset Features PnP/PCI Configurations Frequency/Voltage Control Integrated Peripherals Intel OnChip IDE DeviceOn-Chip Primary/Secondary PCI IDE IDE Primary/Secondary/Master/Slave PIOInit Display First Onboard I/O Chip SetupIntel OnChip PCI Device Uart Mode Select IR Transmission DelayUR2 Duplex Mode Use IR PinsPower Management Run Vgabios if S3 ResumePower Management Acpi Suspend TypeSuspend Mode HDD Power DownVideo Off Method Video Off In SuspendDate of Month Alarm Time hh mm ss AlarmReload Global Timer Events USB KB Wake-up From S3Hardware Monitor Case Open WarningLoad Defaults Load System Default SettingsLoad System Turbo Settings Load Cmos From BiosExit Without Saving Save & Exit SetupExit Menu Software List Software SetupSoftware Installation Troubleshooting ProblemProblem Problem Specification Hardward installationSoftware Installation Appendix I：Appendix II： Appendix III： Albatron USA Inc