Albatron Technology PX845PEV-800 manual Problem

Page 45

Albatron Anniversary Special Edition PX845PEV-800

Problem 4:

System only boots from the CD-ROM. The hard disk can be read and applications can be used but booting from the hard disk is impossible.

Causes: Hard Disk boot sector has been corrupted.

Solutions: Back up data and applications files. Reformat the hard drive. Re-install applications and data using backup disks.

Problem 5:

Error message reading “SECTOR NOT FOUND” displays and the system does not allow certain data to be accessed.

Causes: There are many reasons for this such as virus intrusion or disk failure.

Solutions: Back up any salvageable data. Then perform a low level format, partition, and then a high level format of the hard drive. Re-install all saved data when completed.

Problem 6:

Screen message says “Invalid Configuration” or “CMOS Failure.”

Causes: Incorrect information entered into the BIOS setup program.

Solutions: Review system’s equipment. Reconfigure the system.

Problem 7:

The Screen is blank.

Causes: No power to monitor.

Solutions: Check the power connectors to the monitor and to the system.

Problem 8:

Blank screen.

Causes:

1.Memory problem.

2.Computer virus. Solutions:

1.Reboot computer. Reinstall memory. Make sure that all memory modules are securely installed.

2.Use anti-virus programs to detect and clean viruses.

Problem 9:

Screen goes blank periodically.

Causes: Screen saver is enabled.

Solutions: Disable screen saver.

42

Image 45
Contents Albatron PX845PEV-800 Copyright Contents Introduction Getting StartedCPU SpecificationsLAN Bios Function Content Location Quick Content TableConfiguration Subject Hardware InstallationCPU Socket 478 Configuration Steps CPU Processor InstallationFAN Headers Frequency / Voltage ControlFormulas Watch Dog TimerRAM Module Installation Memory InstallationDIMM1 DIMM2 DIMM3 Memory installation noteBack Panel Configuration PS/2 Mouse & PS/2 Keyboard Connectors KB/MSUSB & LAN Connectors USB/LAN Serial and Parallel Interface Ports Serial Interface COM1/ COM2Parallel Interface Port PRT Front Panel Indicator SW/LED Connector ConfigurationIrDA Infrared Connector Speaker Speaker ConnectorHard Disk Connectors IDE1/ IDE2 Floppy Disk Connector FDCIDE1 Primary IDE Connector IDE2 Secondary IDE ConnectorHeaders & Jumpers Case Open Warning connector Case OpenFront USB Headers USB2 / USB3 USB Bracket 2 Ports or 4 PortsJP1 Clear Cmos Jumper JP1Slots AGP Accelerated Graphics Port SlotPCI Peripheral Component Interconnect Slots ATX Power Connector ATX12V & Atxpwr Power Supply AttachmentsBios Setup Key Function Supported CPUsMain Menu Main Menu Setup Configuration Options First /Second/Third/ Boot Device Advanced Bios FeaturesBoot Other Device Boot Up Floppy SeekBoot Up NumLock Status Quick Power On Self TestTypematic Rate Setting Typematic Delay MsecAdvanced Chipset Features PnP/PCI Configurations Frequency/Voltage Control Intel OnChip IDE Device Integrated PeripheralsOn-Chip Primary/Secondary PCI IDE IDE Primary/Secondary/Master/Slave PIOOnboard I/O Chip Setup Intel OnChip PCI DeviceInit Display First IR Transmission Delay Uart Mode SelectUR2 Duplex Mode Use IR PinsRun Vgabios if S3 Resume Power ManagementPower Management Acpi Suspend TypeHDD Power Down Suspend ModeVideo Off Method Video Off In SuspendTime hh mm ss Alarm Date of Month AlarmReload Global Timer Events USB KB Wake-up From S3Case Open Warning Hardware MonitorLoad System Default Settings Load DefaultsLoad System Turbo Settings Load Cmos From BiosSave & Exit Setup Exit MenuExit Without Saving Software Setup Software InstallationSoftware List Problem TroubleshootingProblem Problem Hardward installation SpecificationSoftware Installation Appendix I:Appendix II: Albatron USA Inc Appendix III: