DFI system board, 915g-tmgf, 915gv-tml user manual Package Checklist

Page 15

Introduction

1.3Package Checklist

;One system board

;One IDE cable for UltraDMA 33/66/100 IDE drives

;One 34-pin floppy disk drive cable

;Two Serial ATA data cables

;One Serial ATA power cable

;One I/O shield

;One “Mainboard Utility” CD

;One user’s manual

If any of these items are missing or damaged, please contact your dealer or sales representative for assistance.

1

15

Image 15

Contents 83800441 915G-TMGF 915GV-TMLAll Rights Reserved CopyrightFCC and DOC Statement on Class B About this Manual Table of Contents Introduction Appendix B System Error MessagesAppendix C Troubleshooting Appendix a Enabling the Hyper-Threading TechnologySystem Memory SpecificationsProcessor ChipsetHardware Monitor Onboard VGA FeaturesOnboard Audio Features Onboard LAN FeaturesExpansion Slots ConnectorsIDE Interface Rear Panel I/O PortsHyper-Threading Technology Functionality Requirements Special Features of the System BoardPCI Express Intel Graphics Media AcceleratorChannel Audio CPU Overheat ProtectionWake-On-Ring Dual Function Power ButtonIrDA Interface USB PortsWake-On-USB Keyboard/Mouse RTC Timer to Power-on the SystemWake-On-LAN Wake-On-PS/2 Keyboard/MouseAcpi STR AC Power Failure RecoveryPackage Checklist Hardware Installation Hardware Installation915GV Channel a DDR 1 and DDR Channel B DDR 3 and DDR System MemoryVirtual Single Channel VSC Dynamic Mode AddressingBios Setting Single Channel SCOn the next Hardware Installation Hardware Installation Installing the Dimm Installing the CPU CPUOverview Tab Gold mark Pin 1 of the socket Once the CPU is in place, move the cover down Use only certified fan and heat sink Installing the Fan and Heat SinkHole Jumper Settings Clear Cmos DataIf you encounter the following Type Y and press Enter Hardware Installation 2 PS/2 Power Select Hardware Installation USB Power Select Line-in Line-out Mic-in Rear Panel I/O PortsParallel 13941Bios Setting Hardware Installation 1 PS/2 Mouse and PS/2 Keyboard PortsHardware Installation Serial Port Enhanced Parallel Port Function Hardware Installation Parallel PortStandard Parallel Port Extended Capabilities PortDriver Installation Hardware Installation VGA PortHardware Installation Ieee 1394 915G-TMGF only Hardware Installation USB Ports Hardware Installation PXE LAN Boot ROM Hardware Installation 7 RJ45 LAN PortAs rear right/left speaker out Hardware Installation Audio Rear Audio and Front AudioRear Panel Audio Mic-in PinkFront Audio CD-in Internal Audio Connector I/O ConnectorsHardware Installation 2 S/PDIF Connecting the Floppy Disk Drive Cable Hardware Installation Floppy Disk Drive ConnectorHardware Installation Serial ATA Connectors Connecting the IDE Disk Drive Cable Hardware Installation IDE Disk Drive ConnectorAdding a Second IDE Disk Drive Hardware Installation IrDA Connector Hardware Installation Cooling Fan Connectors Hardware Installation Power Connectors ATX-SW ATX Power Switch Hardware Installation Front Panel ConnectorsReset Reset Switch Speaker Speaker ConnectorPWR-LED Power/Standby LED Hardware Installation PCI Express x16 and x1 Slots When you press Del, the main menu screen will appear Award Bios Setup UtilityBios Setup Press DEL to enter setupBios Setup Standard Cmos Features DateTime IDE HDD Auto Detection IDE Channel 0 Master/Slave and IDE Channel 1 Master/SlaveHead Access ModeCapacity CylinderBase Memory Non-fatal errorVideo Halt OnExtended Memory Total MemoryDisplays the total memory available in the system Bios Setup Advanced Bios Features CPU Feature Delay Prior To ThermalTM2 Bus VID NX Bios Control Hard Disk Boot PriorityLimit Cpuid MaxVal CPU L1 & L2 Cache This field is used to enable or disable the CPU’s L3 cacheQuick Power On Self Test Virus WarningGate A20 Option Boot Up Floppy SeekBoot Up NumLock Status Swap Floppy DriveTypematic Rate Chars/Sec Typematic Rate SettingTypematic Delay Msec Apic ModeOptions are Yes and No MPS Version Control for OSOS Select for Dram 64MB Report No FDD For WINBios Setup Advanced Chipset Features Dram Timing SelectableThis field is used to select the timing of the Dram Video Bios Cacheable Dram RAS# to CAS# DelayPrecharge Delay tRAS System Bios CacheablePCI Express Port 1 to PCI Express Port PCI-E Compliancy ModeMemory Hole At 15M-16M PCI Express Root Port FuncOn-Chip Frame Buffer Size 3.12 PEG/Onchip VGA ControlPEG Force On-Chip Video Memory SizeBoot Display OnChip IDE Device Bios Setup Integrated PeripheralsIDE Primary Master PIO and IDE Primary Slave PIO IDE HDD Block ModeIDE DMA Transfer Access On-Chip Primary PCI IDEOn-Chip Serial ATA Setting USB Keyboard Support Onboard DeviceUSB Controller USB 2.0 ControllerAC97 Audio Auto Select this option when using the onboard audioDisabled Select this option when using a PCI sound card This field is used to enable or disable the onboard LANSuper IO Device Power On FunctionUR2 Duplex Mode KB Power On PasswordHot Key Power On Uart Mode SelectThis is used to select a DMA channel of the parallel port Parallel Port ModeECP Mode Use DMA Onboard Parallel PortAcpi Suspend Type Bios Setup Power Management SetupRun Vgabios if S3 Resume Acpi FunctionSuspend Type Power ManagementVideo Off Method Video Off In SuspendCPU Thermal-Throttling Suspend ModeHDD Power Down Soft-Off by PWR-BTTNWake-Up By PCI Card Power On By RingResume By Alarm Date of Month AlarmReload Global Timer Events Time hhmmss AlarmBios Setup 6 PnP/PCI Configurations Reset Configuration DataInit Display First 6.5 PCI/VGA Palette Snoop Resources Controlled ByRespectively IRQ ResourcesMaximum Payload Size Shutdown Temperature Bios Setup PC Health StatusAuto Detect PCI Clk Bios Setup Frequency/Voltage ControlCPU Clock Ratio This field is used to select the CPU’s frequency ratioCPU Clock Bios Setup Load Fail-Safe Defaults Type Y and press Enter to load the Setup default values Bios Setup Load Optimized DefaultsBios Setup Set Supervisor Password Bios Setup Set User Password Bios Setup Save & Exit Setup Bios Setup Exit Without Saving Updating the Bios 100 Supported Software Drivers, Utilities and Software Applications102 Supported Software Intel Graphics Media Accelerator Driver Supported Software Realtek Audio Driver Supported Software Realtek LAN Driver Supported Software Hardware Monitor Supported Software Microsoft DirectX To install, please follow the steps belowInstallation Notes Supported Software Intel USB 2.0 DriversWindows System requires a minimum of 300 Watt ATX 12V power supply Enabling Hyper-Threading TechnologyEnabling Hyper-Threading Technology 110 111 Error Messages System Error MessageFloppy Disks fail Keyboard is locked out Unlock the key Keyboard error or no keyboard presentBios ROM checksum error System halted Hard Disks failMonitor/Display Troubleshooting ChecklistTroubleshooting Make sure that the monitor’s power switch is onFloppy Drive Power SupplyHard disk failure Troubleshooting Hard DriveSystem Board Keyboard118