DFI system board Hardware Installation Audio Rear Audio and Front Audio, Rear Panel Audio

Page 42

2

Hardware Installation

2.5.8 Audio (Rear Audio and Front Audio)

Line-in

Line-out

Mic-in

Rear Audio

W

Key

AuD_R_Return

AuD_Vcc

GND

2

1

AuD_L_Return

10 9

Front audio

W

Mic N. C. Out	N. C. Out
AuD R	AuD L

Rear Panel Audio

•Line-in (Light Blue)

In a 2-channel or 4-channel mode, this jack is used to connect any audio devices such as Hi-fi set, CD player, tape player, AM/ FM radio tuner, synthesizer, etc. In a 6-channel mode, this jack functions as Center/Subwoofer.

•Line-out (Lime)

In a 2-channel mode, this jack is used to connect a headphone or external speakers. In a 4-channel or 6-channel mode, this jack functions as front right/left speaker out.

•Mic-in (Pink)

In a 2-channel mode, this jack is used to connect an external microphone. In a 4-channel or 6-channel mode, this jack functions

as rear right/left speaker out.

42

Image 42

Contents 915G-TMGF 915GV-TML 83800441Copyright All Rights ReservedFCC and DOC Statement on Class B About this Manual Table of Contents Appendix a Enabling the Hyper-Threading Technology Appendix B System Error MessagesAppendix C Troubleshooting IntroductionChipset SpecificationsProcessor System MemoryOnboard LAN Features Onboard VGA FeaturesOnboard Audio Features Hardware MonitorRear Panel I/O Ports ConnectorsIDE Interface Expansion SlotsIntel Graphics Media Accelerator Special Features of the System BoardPCI Express Hyper-Threading Technology Functionality RequirementsCPU Overheat Protection Channel AudioUSB Ports Dual Function Power ButtonIrDA Interface Wake-On-RingWake-On-PS/2 Keyboard/Mouse RTC Timer to Power-on the SystemWake-On-LAN Wake-On-USB Keyboard/MouseAC Power Failure Recovery Acpi STRPackage Checklist Hardware Installation Hardware Installation915GV System Memory Channel a DDR 1 and DDR Channel B DDR 3 and DDRSingle Channel SC Dynamic Mode AddressingBios Setting Virtual Single Channel VSCOn the next Hardware Installation Hardware Installation Installing the Dimm Installing the CPU CPUOverview Tab Gold mark Pin 1 of the socket Once the CPU is in place, move the cover down Installing the Fan and Heat Sink Use only certified fan and heat sinkHole Jumper Settings Clear Cmos DataIf you encounter the following Type Y and press Enter Hardware Installation 2 PS/2 Power Select Hardware Installation USB Power Select 13941 Rear Panel I/O PortsParallel Line-in Line-out Mic-inHardware Installation 1 PS/2 Mouse and PS/2 Keyboard Ports Bios SettingHardware Installation Serial Port Extended Capabilities Port Hardware Installation Parallel PortStandard Parallel Port Enhanced Parallel Port FunctionHardware Installation VGA Port Driver InstallationHardware Installation Ieee 1394 915G-TMGF only Hardware Installation USB Ports Hardware Installation Hardware Installation 7 RJ45 LAN Port PXE LAN Boot ROMMic-in Pink Hardware Installation Audio Rear Audio and Front AudioRear Panel Audio As rear right/left speaker outFront Audio I/O Connectors CD-in Internal Audio ConnectorHardware Installation 2 S/PDIF Hardware Installation Floppy Disk Drive Connector Connecting the Floppy Disk Drive CableHardware Installation Serial ATA Connectors Hardware Installation IDE Disk Drive Connector Connecting the IDE Disk Drive CableAdding a Second IDE Disk Drive Hardware Installation IrDA Connector Hardware Installation Cooling Fan Connectors Hardware Installation Power Connectors Speaker Speaker Connector Hardware Installation Front Panel ConnectorsReset Reset Switch ATX-SW ATX Power SwitchPWR-LED Power/Standby LED Hardware Installation PCI Express x16 and x1 Slots Press DEL to enter setup Award Bios Setup UtilityBios Setup When you press Del, the main menu screen will appearBios Setup Standard Cmos Features DateTime IDE Channel 0 Master/Slave and IDE Channel 1 Master/Slave IDE HDD Auto DetectionCylinder Access ModeCapacity HeadHalt On Non-fatal errorVideo Base MemoryExtended Memory Total MemoryDisplays the total memory available in the system Bios Setup Advanced Bios Features CPU Feature Delay Prior To ThermalTM2 Bus VID NX Bios Control Hard Disk Boot PriorityLimit Cpuid MaxVal Virus Warning This field is used to enable or disable the CPU’s L3 cacheQuick Power On Self Test CPU L1 & L2 CacheSwap Floppy Drive Boot Up Floppy SeekBoot Up NumLock Status Gate A20 OptionApic Mode Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/SecReport No FDD For WIN MPS Version Control for OSOS Select for Dram 64MB Options are Yes and NoBios Setup Advanced Chipset Features Dram Timing SelectableThis field is used to select the timing of the Dram System Bios Cacheable Dram RAS# to CAS# DelayPrecharge Delay tRAS Video Bios CacheablePCI Express Root Port Func PCI-E Compliancy ModeMemory Hole At 15M-16M PCI Express Port 1 to PCI Express PortOn-Chip Video Memory Size 3.12 PEG/Onchip VGA ControlPEG Force On-Chip Frame Buffer SizeBoot Display Bios Setup Integrated Peripherals OnChip IDE DeviceOn-Chip Primary PCI IDE IDE HDD Block ModeIDE DMA Transfer Access IDE Primary Master PIO and IDE Primary Slave PIOOn-Chip Serial ATA Setting USB 2.0 Controller Onboard DeviceUSB Controller USB Keyboard SupportThis field is used to enable or disable the onboard LAN Auto Select this option when using the onboard audioDisabled Select this option when using a PCI sound card AC97 AudioPower On Function Super IO DeviceUart Mode Select KB Power On PasswordHot Key Power On UR2 Duplex ModeOnboard Parallel Port Parallel Port ModeECP Mode Use DMA This is used to select a DMA channel of the parallel portAcpi Function Bios Setup Power Management SetupRun Vgabios if S3 Resume Acpi Suspend TypeVideo Off In Suspend Power ManagementVideo Off Method Suspend TypeSoft-Off by PWR-BTTN Suspend ModeHDD Power Down CPU Thermal-ThrottlingDate of Month Alarm Power On By RingResume By Alarm Wake-Up By PCI CardTime hhmmss Alarm Reload Global Timer EventsBios Setup 6 PnP/PCI Configurations Reset Configuration DataInit Display First IRQ Resources Resources Controlled ByRespectively 6.5 PCI/VGA Palette SnoopMaximum Payload Size Bios Setup PC Health Status Shutdown TemperatureThis field is used to select the CPU’s frequency ratio Bios Setup Frequency/Voltage ControlCPU Clock Ratio Auto Detect PCI ClkCPU Clock Bios Setup Load Fail-Safe Defaults Bios Setup Load Optimized Defaults Type Y and press Enter to load the Setup default valuesBios Setup Set Supervisor Password Bios Setup Set User Password Bios Setup Save & Exit Setup Bios Setup Exit Without Saving Updating the Bios 100 Drivers, Utilities and Software Applications Supported Software102 Supported Software Intel Graphics Media Accelerator Driver Supported Software Realtek Audio Driver Supported Software Realtek LAN Driver Supported Software Hardware Monitor To install, please follow the steps below Supported Software Microsoft DirectXInstallation Notes Supported Software Intel USB 2.0 DriversWindows System requires a minimum of 300 Watt ATX 12V power supply Enabling Hyper-Threading TechnologyEnabling Hyper-Threading Technology 110 111 Error Messages System Error MessageFloppy Disks fail Hard Disks fail Keyboard error or no keyboard presentBios ROM checksum error System halted Keyboard is locked out Unlock the keyMake sure that the monitor’s power switch is on Troubleshooting ChecklistTroubleshooting Monitor/DisplayPower Supply Floppy DriveTroubleshooting Hard Drive Hard disk failureKeyboard System Board118