DFI system board, 915g-tmgf, 915gv-tml user manual Bios Setup Load Fail-Safe Defaults

Page 93

BIOS Setup

3.1.9 Load Fail-Safe Defaults

The “Load Fail-Safe Defaults” option loads the troubleshooting default values permanently stored in the ROM chips. These settings are not optimal and turn off all high performance features. You should use these values only if you have hardware problems. Highlight this option in the main menu and press <Enter>.

If you want to proceed, type <Y> and press <Enter>. The default settings will be loaded.

3

9 3

Image 93

Contents 83800441 915G-TMGF 915GV-TMLAll Rights Reserved CopyrightFCC and DOC Statement on Class B About this Manual Table of Contents Appendix C Troubleshooting Appendix B System Error MessagesAppendix a Enabling the Hyper-Threading Technology IntroductionProcessor SpecificationsChipset System MemoryOnboard Audio Features Onboard VGA FeaturesOnboard LAN Features Hardware MonitorIDE Interface ConnectorsRear Panel I/O Ports Expansion SlotsPCI Express Special Features of the System BoardIntel Graphics Media Accelerator Hyper-Threading Technology Functionality RequirementsChannel Audio CPU Overheat ProtectionIrDA Interface Dual Function Power ButtonUSB Ports Wake-On-RingWake-On-LAN RTC Timer to Power-on the SystemWake-On-PS/2 Keyboard/Mouse Wake-On-USB Keyboard/MouseAcpi STR AC Power Failure RecoveryPackage Checklist Hardware Installation Hardware Installation915GV Channel a DDR 1 and DDR Channel B DDR 3 and DDR System MemoryBios Setting Dynamic Mode AddressingSingle Channel SC Virtual Single Channel VSCOn the next Hardware Installation Hardware Installation Installing the Dimm Installing the CPU CPUOverview Tab Gold mark Pin 1 of the socket Once the CPU is in place, move the cover down Use only certified fan and heat sink Installing the Fan and Heat SinkHole Jumper Settings Clear Cmos DataIf you encounter the following Type Y and press Enter Hardware Installation 2 PS/2 Power Select Hardware Installation USB Power Select Parallel Rear Panel I/O Ports13941 Line-in Line-out Mic-inBios Setting Hardware Installation 1 PS/2 Mouse and PS/2 Keyboard PortsHardware Installation Serial Port Standard Parallel Port Hardware Installation Parallel PortExtended Capabilities Port Enhanced Parallel Port FunctionDriver Installation Hardware Installation VGA PortHardware Installation Ieee 1394 915G-TMGF only Hardware Installation USB Ports Hardware Installation PXE LAN Boot ROM Hardware Installation 7 RJ45 LAN PortRear Panel Audio Hardware Installation Audio Rear Audio and Front AudioMic-in Pink As rear right/left speaker outFront Audio CD-in Internal Audio Connector I/O ConnectorsHardware Installation 2 S/PDIF Connecting the Floppy Disk Drive Cable Hardware Installation Floppy Disk Drive ConnectorHardware Installation Serial ATA Connectors Connecting the IDE Disk Drive Cable Hardware Installation IDE Disk Drive ConnectorAdding a Second IDE Disk Drive Hardware Installation IrDA Connector Hardware Installation Cooling Fan Connectors Hardware Installation Power Connectors Reset Reset Switch Hardware Installation Front Panel ConnectorsSpeaker Speaker Connector ATX-SW ATX Power SwitchPWR-LED Power/Standby LED Hardware Installation PCI Express x16 and x1 Slots Bios Setup Award Bios Setup UtilityPress DEL to enter setup When you press Del, the main menu screen will appearBios Setup Standard Cmos Features DateTime IDE HDD Auto Detection IDE Channel 0 Master/Slave and IDE Channel 1 Master/SlaveCapacity Access ModeCylinder HeadVideo Non-fatal errorHalt On Base MemoryExtended Memory Total MemoryDisplays the total memory available in the system Bios Setup Advanced Bios Features CPU Feature Delay Prior To ThermalTM2 Bus VID NX Bios Control Hard Disk Boot PriorityLimit Cpuid MaxVal Quick Power On Self Test This field is used to enable or disable the CPU’s L3 cacheVirus Warning CPU L1 & L2 CacheBoot Up NumLock Status Boot Up Floppy SeekSwap Floppy Drive Gate A20 OptionTypematic Delay Msec Typematic Rate SettingApic Mode Typematic Rate Chars/SecOS Select for Dram 64MB MPS Version Control for OSReport No FDD For WIN Options are Yes and NoBios Setup Advanced Chipset Features Dram Timing SelectableThis field is used to select the timing of the Dram Precharge Delay tRAS Dram RAS# to CAS# DelaySystem Bios Cacheable Video Bios CacheableMemory Hole At 15M-16M PCI-E Compliancy ModePCI Express Root Port Func PCI Express Port 1 to PCI Express PortPEG Force 3.12 PEG/Onchip VGA ControlOn-Chip Video Memory Size On-Chip Frame Buffer SizeBoot Display OnChip IDE Device Bios Setup Integrated PeripheralsIDE DMA Transfer Access IDE HDD Block ModeOn-Chip Primary PCI IDE IDE Primary Master PIO and IDE Primary Slave PIOOn-Chip Serial ATA Setting USB Controller Onboard DeviceUSB 2.0 Controller USB Keyboard SupportDisabled Select this option when using a PCI sound card Auto Select this option when using the onboard audioThis field is used to enable or disable the onboard LAN AC97 AudioSuper IO Device Power On FunctionHot Key Power On KB Power On PasswordUart Mode Select UR2 Duplex ModeECP Mode Use DMA Parallel Port ModeOnboard Parallel Port This is used to select a DMA channel of the parallel portRun Vgabios if S3 Resume Bios Setup Power Management SetupAcpi Function Acpi Suspend TypeVideo Off Method Power ManagementVideo Off In Suspend Suspend TypeHDD Power Down Suspend ModeSoft-Off by PWR-BTTN CPU Thermal-ThrottlingResume By Alarm Power On By RingDate of Month Alarm Wake-Up By PCI CardReload Global Timer Events Time hhmmss AlarmBios Setup 6 PnP/PCI Configurations Reset Configuration DataInit Display First Respectively Resources Controlled ByIRQ Resources 6.5 PCI/VGA Palette SnoopMaximum Payload Size Shutdown Temperature Bios Setup PC Health StatusCPU Clock Ratio Bios Setup Frequency/Voltage ControlThis field is used to select the CPU’s frequency ratio Auto Detect PCI ClkCPU Clock Bios Setup Load Fail-Safe Defaults Type Y and press Enter to load the Setup default values Bios Setup Load Optimized DefaultsBios Setup Set Supervisor Password Bios Setup Set User Password Bios Setup Save & Exit Setup Bios Setup Exit Without Saving Updating the Bios 100 Supported Software Drivers, Utilities and Software Applications102 Supported Software Intel Graphics Media Accelerator Driver Supported Software Realtek Audio Driver Supported Software Realtek LAN Driver Supported Software Hardware Monitor Supported Software Microsoft DirectX To install, please follow the steps belowInstallation Notes Supported Software Intel USB 2.0 DriversWindows System requires a minimum of 300 Watt ATX 12V power supply Enabling Hyper-Threading TechnologyEnabling Hyper-Threading Technology 110 111 Error Messages System Error MessageFloppy Disks fail Bios ROM checksum error System halted Keyboard error or no keyboard presentHard Disks fail Keyboard is locked out Unlock the keyTroubleshooting Troubleshooting ChecklistMake sure that the monitor’s power switch is on Monitor/DisplayFloppy Drive Power SupplyHard disk failure Troubleshooting Hard DriveSystem Board Keyboard118