Klark Teknik DN9652 Checking/replacing the mains fuse, Special accessories, Optional equipment

Page 48

Checking/replacing the mains fuse

Checking/replacing the mains fuse

The equipment must be independently isolated from the mains voltage supply before any attempt is made to change the protective fuse. The fuse and its cover must always be replaced before the equipment is reconnected to the mains voltage supply.

Only use the correct replacement type when changing the fuse. Fuse specification is printed on the rear cover.

To remove the fuse, pull out the fuse drawer (see “Mains input” on page 16). Then, prise out the fuse from the furthest compartment (the nearest compartment is for a spare fuse); a small, flat-bladed screwdriver may be useful for this.

Insert a new fuse in the rear fuse compartment, and close the drawer.

After replacing a fuse, check that the unit is working properly.

Always ensure that there is a spare fuse available.

Special accessories

To comply with part 15 of the FCC Rules, any special accessories (that is, items that cannot be readily obtained from multiple retail outlets) supplied with this equipment must be used with this equipment; do not use any alternatives, as they may not fulfil the RF requirement.

Optional equipment

Unless advised otherwise, optional equipment must only be installed by service personnel and in accordance with the appropriate assembly and usage regulations.

Equipment disposal

When this equipment has come to the end of its useful life, its disposal may come under the DIRECTIVE 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Hazardous substances in WEEE contaminate water, soil and air and ultimately put at risk our environment and health. The directive aims to minimize the impacts of WEEE on the environment during their life times and when they become waste.

The WEEE directive addresses the disposal of products when they have reached the end of their life and contributes to the reduction of wasteful consumption of natural resources. This will help to reduce pollution, and protect the environment and ourselves.

If this equipment carries a ‘crossed-out wheelie bin’ (shown left), please do not dispose of WEEE as unsorted municipal waste but collect and dispose of in accordance with local WEEE legislation. The horizontal bar underneath indicates that the product was placed on the EU market after 13th August 2005.

For WEEE disposal, see our website at www.klarkteknik.com for information.

 

DN9650/DN9652 Network Bridge

34

Operator Manual

Image 48
Contents DN9650/DN9652 Page Important Safety Instructions Instructions DE Sécurité Importantes Klark Teknik Hereby declares that the following productPage SVP, Midas Klark Teknik AVP, Product Development Page Licences Page GNU General Public License GPL Page Contents Contents Installation Getting StartedUnpacking Connecting up the DN965X Getting StartedPowering the unit Powering the unitTo switch the unit on/off Configuring the unit for the first time Connecting a DN965X to a computerConfiguring the unit for the first time Getting Started Overview About the DN965X unitsKey features OverviewHost software version and updates Host software version and updatesChanging the network module Service and support About this manualTrademarks Front Panel Front Panel Klark Teknik roundel Has a blue backlightDN9650 Asrc LED status DN9652 Asrc LED statusFront Panel Rear Panel Item DescriptionControl connector Mains inputClock section AES50 section DN9650 onlyConfiguring the DN965X About DN965X configurationAbout the web browser interface Configuring the DN965X Item Screen elementSetting up a network module To configure a network module cardChanging the displayed text Changing the displayed textClocking options To change the clocking options of a network moduleClocking Options Ethernet IP Addressing Ethernet IP AddressingTo change the IP address of the DN965X Updating the unit’s host software TAR files and recommended file upload orderSoftware Updating the unit’s host software Default IP address Default display Using a Madi module as a Madi split To configure the Madi module as a Madi splitOperation Operation Appendix a Technical Specification Appendix a Technical Specification Appendix B Functional Block Diagrams Appendix B Functional Block Diagrams DN9650DN9652 DN9652Appendix B Functional Block Diagrams Appendix C Service Information Restoring the factory defaultsRoutine maintenance CleaningSpecial accessories Checking/replacing the mains fuseOptional equipment Equipment disposal