Xtant X604 Installation Instructions, Input Sensitivity Adjustment, Crossover Frequencies & SIP’s

Page 4

Installation Instructions

English

 

 

This document has been crafted to make installation, system design and trouble+ shooting, a quick and easy process*

Installation Sequence

Remove Amplifier Cover:

Loosen allen head screws and lift+off cover* Do not remove protective covering on stainless steel lid until installation is complete*

Temporarily Mount Amplifier:

The amplifier is designed to be anchored through the four (") holes located on the circuit board/base assembly*

Mark Wires for Termination and Remove X%(":

Determine wire lengths for Power, Ground, Remote, & speaker cables* Mark for cutting/termination* Remove X%(" before cutting and terminating all wires*

CAUTION: stripping wires over the circuit board will cause product failure*

Crossover Set+up:

Adjust crossover mode jumpers at your work bench* Also, change crossover frequency SIP’s if desired* Refer to crossover modes of operation on opposite page*

Input Sensitivity:

Make initial adjustment to input gain at your work bench* To increase input gain, place jumper in the .!( dB position* To decrease input gain, place jumper in the (, +$(, or +!( dB position* Refer to Input Sensitivity Adjustment on back panel for more information*

Mount the Amplifier and make all connections:

NOTE: Place service jumper in off position before making any connections* Install

the amplifier and make all wire connections* i*e:*Speaker, Power, Remote, Ground, and RCA input*

Double Check All Connections! Turn On Amplifier*

Place service jumper in the on position, check red LED, it should be on*

Adjust Left and Right Front as well as Left and Right Rear Amplifier Output Levels*

Adjust Noise Gate Threshold (if used)

Turn noise gate on and adjust the threshold by turning clockwise to increase sensitivity* The green LED will illuminate*

After Fine Tuning the System:

Remove protective covering from amplifier and clean per the maintanence section on page & of the Owner’s Manual* Attach cover to base*

4

English

Input Sensitivity Adjustment

 

The X%(" offers five ()) input gain settings* The adjustment runs in $( dB steps from +!( dB to . !( dB* This wide range of adjustment allows the X%(" to accept input voltages from $(( mV to $# V* Adjustment is made by installing a jumper across the associated input voltage/pin location* Refer to the illustration on the reverse side of this document prior to setting the input sensitivity*

Crossover Frequencies & SIP’s

The X%(" is equipped with independent Front and Rear crossovers* Each crossover is controlled by two (!) crossover mode jumpers labeled AMP & LINE XOVR* The header jumper labeled AMP XOVR control the crossover function as it applies to the X%("’s Front (stereo) and Rear (stereo) amplifier* The modes of operation are: Position $ / Bypass (Full Range), Position ! / High Pass, and Position ' / Low Pass and Position "/Band Pass (See insert)

The two (!) header jumpers labeled LINE XOVR control the crossover function as it applies to the X%("’s Front and Rear RCA Line Outputs* The modes of oper+ ation are: Position $ / Bypass (Full Range), Position ! / High Pass, and Position

'/ Low Pass* (See insert)

The High and Low Pass frequencies are determined by the Frequency Modules (SIPs) installed in the eight (-) SIP sockets pictured on the insert*

Crossover Frequencies & SIP’s

The following is a chart of Xtant’s available frequencies* The frequency SIP “ID Code” printed on the SIP and the associated frequency value is detailed below*

SIP Number

Frequency

!!"

)( Hz

$'"

#( Hz

$$"

-( Hz

$("

&( Hz

%-'

$!( Hz

)%'

$)( Hz

!#'

'(( Hz

$)'

)(( Hz

$('

#(( Hz

#)!

$ kHz

!"!

' kHz

$-!

" kHz

$)!

) kHz

The X%(" is shipped from the factory with &( Hz HiPass and LowPass frequency SIP’s installed* To change a frequency, simply remove the resistor SIP and replace it with the appropriate SIP value to achieve the desired frequency*

The Low and High Pass frequencies are independent* Any combination of the available frequency SIP’s may be used*

5

Image 4
Contents XT000472 4/01 NDM172 Table of contents Your Xtant X604 amplifier EnglishSafeguardsWelcome Installation Instructions Input Sensitivity AdjustmentInstallation Sequence Crossover Frequencies & SIP’sStandard Features Xtant X604 SpecificationsOptional Performance Upgrades English EnglishCleaning/TechnicalFrançais Votre Amplificateur Xtant BienvenueConsignes de Sécurité Caractéristiques StandardInstructions d’Installation Séquences d’InstallationFrançais Réglage de la Sensibilité d’Entrée Modes de fonctionnement des filtres actifsRéglage de Niveau par Télécommande Déportée RGM Modules OptionnelsModule de Correction Paramétrique PQM Equaliseur de Basse Fréquence LFQIhr Xtant X604 Verstärker Nettoyage/Services Techniques FrançaisWillkommen Sicherheitsmaßnahmen Deutsch DeutschStandardfunktionenInstallationsanleitung Deutsch InstallationsreihenfolgeEinstellung der EingangsempfindlichkeitXtant X604 Technische Daten Parametrisches Equalizer-Modul PQMNiederfrequenz-Equalizer LFQ Fernbedienungs-Verstärkermodul Remote Gain Module/RGMAmplificador Xtant Reinigung/ServiceDeutschBienvenido PrecaucionesEspañol Características EstándarSecuencia de Instalación Instrucciones de InstalaciónFrecuencias de Crossover y MBS Especificaciones Técnicas del XtantMódulo de Ecualización Paramétrica PQM Ecualizador de Baja Frecuencia LFQCircuito del ventilador Limpieza de la Cubierta de Acero InoxidableServicio Técnico

X604 specifications

The Xtant X604 is an innovative and versatile multi-channel amplifier that has gained recognition in the audio industry for its exceptional performance and advanced technology. Designed for both car audio enthusiasts and professional installations, the X604 offers a range of features that enhance sound quality and provide flexibility for various applications.

One of the standout features of the Xtant X604 is its ability to deliver impressive power output. With a continuous power rating of 75 watts per channel at 4 ohms and 100 watts at 2 ohms, it can easily drive a variety of speaker configurations, providing users with an immersive listening experience. The amplifier is configured in a class A/B design, which combines the efficiency of class D amplification with the sound quality associated with class A designs. This results in low distortion and rich audio reproduction across the frequency spectrum.

The X604 incorporates advanced technologies that contribute to its performance. It features a high-pass and low-pass crossover system that allows users to tailor their audio to their preference, ensuring that high frequencies remain clear and crisp while low frequencies deliver a powerful punch. Additionally, it includes a variable bass boost feature, enabling users to enhance low-end performance according to their listening preferences or specific music genres.

Another significant aspect of the Xtant X604 is its compact design, making it suitable for installations with space constraints. Despite its smaller form factor, the amplifier is built with robust materials, ensuring durability and long-lasting performance even under demanding conditions. The heat dissipation system is also noteworthy, as it prevents overheating during extended use, thereby enhancing reliability.

Installation is made easy with the X604 due to its thoughtful layout, which includes well-placed connections and a clear user interface. The amplifier is also compatible with a variety of input sources, from traditional head units to modern digital sources, providing users with versatility.

In conclusion, the Xtant X604 stands out within its category for its combination of power, flexibility, and advanced technologies. Its listening experience is enriched by high-quality audio reproduction, making it an excellent choice for car audio enthusiasts seeking to upgrade their sound system. With its array of features, robust build, and user-friendly design, the X604 is a reliable choice for anyone looking to enhance their audio setup.