Pentair 8 and 4 important safety instructions Important Safety Precautions

Page 5

iii

IMPORTANT SAFETY PRECAUTIONS (Continued)

WARNING To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.

WARNING The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia in hot tubs and spas.

WARNING Control System is intended to control heaters with built-in high limit circuits ONLY.

Failure to do so may cause property damage or personal injury.

WARNING Do not use this product to control an automatic pool cover. Swimmers may become entrapped underneath the cover.

WARNING For units intended for use in other than single-family dwellings, a clearly labeled emergency switch shall be provided as part of the installation. The switch shall be readily accessible to the occupants and shall be installed at least

10 feet (3.05 m) away, adjacent to, and within sight of, the unit.

CAUTION Except for listed spa-side remote controls, install a minimum of five (5) feet from the inside wall of the pool and spa.

FCC Standard - 47 CFR Part 15, Subpart C (Section 15.247). This version is limited to chapter 1 to chapter 11 by specified firmware controlled in the U.S.A.

Canada - Industry Canada (IC) - The IntelliChlor device complies with RSS210 of Industry Canada. (1999). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Instruction to user - The IntelliChlor device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The IntelliChlor device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by switching the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Note: The user is cautioned that changes and modifications made to the IntelliChlor device without the approval of the manufacturer could void the user’s authority to operate this equipment.

EasyTouch Load Center Installation Guide

Page 4 Page 6
Image 5
Page 4 Page 6
Contents EasyTouch 8 520583 Rev B 12/09/05 Contents Important Notice Read and Follow all Safety InstructionsImportant Safety Precautions Technical Support General Installation InformationAbout this manual EasyTouch 8 and 4 Pool and Spa Control System Kit ContentsEasyTouch Accessory Equipment Required Tools EasyTouch System Installation Steps SummaryPlumbing Requirements Equipment Location Recommended Hydraulic Schematic for Single Body System EasyTouch Load Center Location EasyTouch Load Center High Voltage ConnectionsTemperature sensors Preparing the EasyTouch Load Center Enclosure Mounting the EasyTouch Load Center Removing Electrical Conduit Knockouts Installing Conduit and Wire to the EasyTouch Load Center Installing Conduit and Wire to the EasyTouch Load Center EasyTouch Motherboard Connections Accessing the EasyTouch Motherboard Installing Auxiliary Relays Installing Valve Actuators Water Temperature Sensor Installing and Connecting Temperature SensorsAmbient Air Temperature Freeze Protection Sensor Solar Temperature Sensor OptionalConnecting the Heater Thermostat Connecting the IntelliChlor Cell Retaining Screws IntelliChlor transformer and filter Rewiring the IntelliChlor Transformer for 115 VACEasyTouch System Test EasyTouch System Start-UpCheck Electronics Verifying IntelliChlor power EasyTouch System Wiring Diagram Glossary Page 520583 Rev B

8 and 4 specifications

Pentair is renowned for its innovative solutions in water and fluid management, and the Pentair 8 and 4 series are prime examples of their commitment to delivering high-performance products. These series are designed for both residential and commercial applications, showcasing advanced features and technologies that cater to diverse needs.

The Pentair 8 series is known for its robust performance and reliability. It incorporates a powerful motor designed to ensure efficient water circulation and filtration. The 8 series stands out with its user-friendly interface, enabling effortless adjustments and monitoring. The built-in diagnostic features provide real-time feedback, ensuring users can maintain optimal operation without ongoing manual checks. Additionally, the Pentair 8 series emphasizes energy efficiency, reducing power consumption and lowering operational costs.

On the other hand, the Pentair 4 series focuses on compactness and versatility. It is engineered to fit in tight spaces, making it an ideal choice for urban environments where space is a premium. Though smaller in size, the 4 series does not compromise on performance. It utilizes innovative pump technology that maximizes flow while minimizing noise levels. This feature is particularly beneficial for residential applications, where maintaining a quiet environment is essential. The 4 series also includes a range of customizable options, allowing users to tailor the system to their specific requirements.

Both the 8 and 4 series share a commitment to durability and longevity. They are constructed with high-quality materials designed to withstand harsh environmental conditions. This durability reduces the frequency of maintenance and replacement, ultimately providing better value to users.

In summary, the Pentair 8 and 4 series offer a blend of performance, efficiency, and adaptability. Their advanced features, such as energy-efficient motors, user-friendly interfaces, and robust construction, make them suitable for a variety of applications. Whether for residential or commercial use, Pentair continues to set the standard in water management solutions, ensuring both convenience and peace of mind for users. To meet the diverse needs of its clientele, Pentair consistently innovates, ensuring their products remain at the forefront of technology and sustainability.
Top Page Image Contents