Pentair 8 and 4 Installing and Connecting Temperature Sensors, Water Temperature Sensor

Page 23

17

Installing and Connecting Temperature Sensors

Water Temperature Sensor

To install the water sensor:

1.Drill a 5/16 in. hole in the plumbing between the filter pump and filter.

2.Insert tip of sensor into the hole. Use the band clamp to secure the sensor to the pipe. Tighten the clamp just enough so that the o-ring begins to flatten. Do not overtighten

3.At the EasyTouch load center, route the wire up through the low voltage raceway to the motherboard.

4.Fasten the cable to the plumbing with cable ties.

5.Cut off the excess wire and the strip conductors ¼ inch. Insert the wires into the WATER screw terminals (J21) on right-side of the motherboard. For motherboard connection details, refer to “EasyTouch Motherboard Connections,” on page 13. For wiring details, refer to EasyTouch System Wiring Diagram,” on page 23.

Ambient Air Temperature (Freeze Protection) Sensor

To install the air sensor:

1Mount the sensor in the open air, in a shaded area, away from air conditioners. During the winter months, to avoid freeze damage to pool and spa equipment, mount the air sensor in a shaded area to assure proper temperature readings.

2Route the wire through the low voltage raceway to the motherboard.

3Fasten the cable to the plumbing with cable ties.

4Cut off the excess wire and the strip conductors ¼ in. Insert the wires into the AIR screw terminals (J21) on right side of the motherboard.

Solar Temperature Sensor (Optional)

To install the solar sensor:

1Mount the sensor on a flat surface, with the same exposure to sun as the solar collectors (next to the collectors is recommended). Do not let the sensor touch the panels.

2If necessary, splice a two-conductor extension wire to the sensor. Route the wire to the load center and up through the low voltage raceway to the motherboard.

3Strip the conductors ¼ in. Insert the wires into the SOLAR screw terminals (J21) on right side of the motherboard.

EasyTouch Load Center Installation Guide

Page 22 Page 24
Image 23
Page 22 Page 24
Contents EasyTouch 8 520583 Rev B 12/09/05 Contents Important Notice Read and Follow all Safety InstructionsImportant Safety Precautions Technical Support General Installation InformationAbout this manual EasyTouch 8 and 4 Pool and Spa Control System Kit ContentsEasyTouch Accessory Equipment Required Tools EasyTouch System Installation Steps SummaryPlumbing Requirements Equipment Location Recommended Hydraulic Schematic for Single Body System EasyTouch Load Center Location EasyTouch Load Center High Voltage ConnectionsTemperature sensors Preparing the EasyTouch Load Center Enclosure Mounting the EasyTouch Load Center Removing Electrical Conduit Knockouts Installing Conduit and Wire to the EasyTouch Load Center Installing Conduit and Wire to the EasyTouch Load Center EasyTouch Motherboard Connections Accessing the EasyTouch Motherboard Installing Auxiliary Relays Installing Valve Actuators Solar Temperature Sensor Optional Installing and Connecting Temperature SensorsWater Temperature Sensor Ambient Air Temperature Freeze Protection SensorConnecting the Heater Thermostat Connecting the IntelliChlor Cell Retaining Screws IntelliChlor transformer and filter Rewiring the IntelliChlor Transformer for 115 VACEasyTouch System Test EasyTouch System Start-UpCheck Electronics Verifying IntelliChlor power EasyTouch System Wiring Diagram Glossary Page 520583 Rev B

8 and 4 specifications

Pentair is renowned for its innovative solutions in water and fluid management, and the Pentair 8 and 4 series are prime examples of their commitment to delivering high-performance products. These series are designed for both residential and commercial applications, showcasing advanced features and technologies that cater to diverse needs.

The Pentair 8 series is known for its robust performance and reliability. It incorporates a powerful motor designed to ensure efficient water circulation and filtration. The 8 series stands out with its user-friendly interface, enabling effortless adjustments and monitoring. The built-in diagnostic features provide real-time feedback, ensuring users can maintain optimal operation without ongoing manual checks. Additionally, the Pentair 8 series emphasizes energy efficiency, reducing power consumption and lowering operational costs.

On the other hand, the Pentair 4 series focuses on compactness and versatility. It is engineered to fit in tight spaces, making it an ideal choice for urban environments where space is a premium. Though smaller in size, the 4 series does not compromise on performance. It utilizes innovative pump technology that maximizes flow while minimizing noise levels. This feature is particularly beneficial for residential applications, where maintaining a quiet environment is essential. The 4 series also includes a range of customizable options, allowing users to tailor the system to their specific requirements.

Both the 8 and 4 series share a commitment to durability and longevity. They are constructed with high-quality materials designed to withstand harsh environmental conditions. This durability reduces the frequency of maintenance and replacement, ultimately providing better value to users.

In summary, the Pentair 8 and 4 series offer a blend of performance, efficiency, and adaptability. Their advanced features, such as energy-efficient motors, user-friendly interfaces, and robust construction, make them suitable for a variety of applications. Whether for residential or commercial use, Pentair continues to set the standard in water management solutions, ensuring both convenience and peace of mind for users. To meet the diverse needs of its clientele, Pentair consistently innovates, ensuring their products remain at the forefront of technology and sustainability.
Top Page Image Contents