Pentair 8 and 4 Installing Conduit and Wire to the EasyTouch Load Center

Page 17

11

Installing Conduit and Wire to the EasyTouch Load Center

Before installing electrical conduit, read the following recommended guidelines:

Determine the number of low and high voltage circuits being used in the EasyTouch load center, the conduit size and runs needed based on the wire size, and the number of conductors within the conduit.

Use 14 minimum to 6 maximum AWG for relay circuits depending on the load requirement. Be sure to follow all regulation safety codes for the number and size of conductors that can be installed in various sizes of conduit.

Power supply cable to the EasyTouch load center must have a minimum supply conductor current of 60 AMP.

Supply circuit must be protected by suitable breaker rated no higher than 125 AMP.

To avoid obstruction into the EasyTouch load center, when using electrical conduit complete the installation of the conduit before concrete is poured. Also, underground conduit should be positioned in well compacted soil. Ensure that all conduit joints are well sealed and watertight.

To install electrical conduit and wires as needed:

WARNING - TO AVOID AN ELECTRICAL HAZARD - Do not connect the power source conductors to the EasyTouch load center circuit breaker until all electrical connections for all loads (heaters, pumps, motorized valves, and lights etc.) have been completed.

Use the one of the three low voltage raceway 3/4" holes located on the underside of the enclosure for the temperature sensor wires (see page 17).

For the AC power wire into the EasyTouch load center from the main circuit breaker at the house, use three conductors, one each for red, black, and white (or red, red and black for 220 VAC). The maximum load is 125 AMP at 120 VAC/240 VAC 60 Hz/50 Hz. These conductors should be secured to supply side of circuit breaker base. Use a 1" conduit run for these power conductors. For the main AC power conduit, it is recommended to use the 1" conduit knockout located directly under the enclosure circuit breaker.

CAUTION All of the electrical wiring methods and materials used to complete the electrical installation of the EasyTouch Pool/Spa Control System must be in accordance with the National Electrical Code or the Canadian Electric Code, as well as any local electrical codes in effect at the time of installation.

CAUTION All electrical materials used for the EasyTouch installation must be accomplished by, or be under the direct supervision of a qualified electrician.

EasyTouch Load Center Installation Guide

Image 17
Contents EasyTouch 8 520583 Rev B 12/09/05 Contents Important Notice Read and Follow all Safety InstructionsImportant Safety Precautions Technical Support General Installation InformationAbout this manual EasyTouch 8 and 4 Pool and Spa Control System Kit ContentsEasyTouch Accessory Equipment Required Tools EasyTouch System Installation Steps SummaryPlumbing Requirements Equipment Location Recommended Hydraulic Schematic for Single Body System EasyTouch Load Center Location EasyTouch Load Center High Voltage ConnectionsTemperature sensors Preparing the EasyTouch Load Center Enclosure Mounting the EasyTouch Load Center Removing Electrical Conduit Knockouts Installing Conduit and Wire to the EasyTouch Load Center Installing Conduit and Wire to the EasyTouch Load Center EasyTouch Motherboard Connections Accessing the EasyTouch Motherboard Installing Auxiliary Relays Installing Valve Actuators Water Temperature Sensor Installing and Connecting Temperature SensorsAmbient Air Temperature Freeze Protection Sensor Solar Temperature Sensor OptionalConnecting the Heater Thermostat Connecting the IntelliChlor Cell Retaining Screws IntelliChlor transformer and filter Rewiring the IntelliChlor Transformer for 115 VACEasyTouch System Test EasyTouch System Start-UpCheck Electronics Verifying IntelliChlor power EasyTouch System Wiring Diagram Glossary Page 520583 Rev B

8 and 4 specifications

Pentair is renowned for its innovative solutions in water and fluid management, and the Pentair 8 and 4 series are prime examples of their commitment to delivering high-performance products. These series are designed for both residential and commercial applications, showcasing advanced features and technologies that cater to diverse needs.

The Pentair 8 series is known for its robust performance and reliability. It incorporates a powerful motor designed to ensure efficient water circulation and filtration. The 8 series stands out with its user-friendly interface, enabling effortless adjustments and monitoring. The built-in diagnostic features provide real-time feedback, ensuring users can maintain optimal operation without ongoing manual checks. Additionally, the Pentair 8 series emphasizes energy efficiency, reducing power consumption and lowering operational costs.

On the other hand, the Pentair 4 series focuses on compactness and versatility. It is engineered to fit in tight spaces, making it an ideal choice for urban environments where space is a premium. Though smaller in size, the 4 series does not compromise on performance. It utilizes innovative pump technology that maximizes flow while minimizing noise levels. This feature is particularly beneficial for residential applications, where maintaining a quiet environment is essential. The 4 series also includes a range of customizable options, allowing users to tailor the system to their specific requirements.

Both the 8 and 4 series share a commitment to durability and longevity. They are constructed with high-quality materials designed to withstand harsh environmental conditions. This durability reduces the frequency of maintenance and replacement, ultimately providing better value to users.

In summary, the Pentair 8 and 4 series offer a blend of performance, efficiency, and adaptability. Their advanced features, such as energy-efficient motors, user-friendly interfaces, and robust construction, make them suitable for a variety of applications. Whether for residential or commercial use, Pentair continues to set the standard in water management solutions, ensuring both convenience and peace of mind for users. To meet the diverse needs of its clientele, Pentair consistently innovates, ensuring their products remain at the forefront of technology and sustainability.