Pentair 8 and 4 EasyTouch System Start-Up, Check Electronics, EasyTouch System Test

Page 27

21

EasyTouch System Start-Up

Perform the following start-up procedures to ensure that the EasyTouch load center is installed correctly. If you need more detailed operating information, refer to the EasyTouch Pool and Spa Control System User’s Guide (P/N 520584).

Before you power up the EasyTouch load center check the following:

Check Electronics

Check that the following plugs are seated correctly on the motherboard:

•Relay connectors - FLTR PUMP - AUX1 - AUX7 (EasyTouch 8), AUX1 - AUX3 (EasyTouch 4)

•Temperature sensors connectors WATER, SOLAR, AIR

•Transformer wire harness (J1) attached to the motherboard.

•Heater control connector ELEC HTR or two-wire screw terminal.

Refer to Summary Installation Steps (page 2) and EasyTouch System Wiring Diagrams, on page 23.

EasyTouch System Test

The following describes how to test the main control panel to activate the heater, valves and pumps. Before testing the system, be sure that all pool and spa equipment has been properly installed and connected to the EasyTouch load center.

Testing Valve Actuators and Filter Pump

Use the following steps to test the valve actuators (CVA24T) for proper rotation.

To test the valve actuators and pump:

1.Power up the EasyTouch load center.

2.Press the Mode button on the main control panel. The display shows “SERVICE”.

3.Press the Valve (V) button to select POOL.

4.Press the Filter Pump (F) button to activate the filter pump. Water will be removed from the pool and returned to the pool.

4.Repeat steps 3 and 4 selecting Fill (Spillway) then Drain.

5.Set both valve actuators (CVA-24T) for suction and return. Use the toggle switch on the rear of the CVA-24T to withdraw and return water from the pool.

Note: With the filter pump operating, if the water is not being removed and returned to the pool, check that the valve actuator plugs are connected correctly on the motherboard.

Testing the auxiliary relays

Affix the auxiliary relay labels to the appropriate AUX buttons on the EasyTouch control panel to identify the connected equipment.

•Press the Mode button to enable “Service” pool mode. Press the Filter Pump button (LED on) and each auxiliary (AUX) circuit button, the Heater and Solar buttons to verify the functions. Press the Mode button twice to return the system to “AUTO” mode when done.

EasyTouch Load Center Installation Guide

Page 26 Page 28
Image 27
Page 26 Page 28
Contents EasyTouch 8 520583 Rev B 12/09/05 Contents Important Notice Read and Follow all Safety InstructionsImportant Safety Precautions Technical Support General Installation InformationEasyTouch 8 and 4 Pool and Spa Control System Kit Contents EasyTouch Accessory EquipmentAbout this manual Required Tools EasyTouch System Installation Steps SummaryPlumbing Requirements Equipment Location Recommended Hydraulic Schematic for Single Body System EasyTouch Load Center Location EasyTouch Load Center High Voltage ConnectionsTemperature sensors Preparing the EasyTouch Load Center Enclosure Mounting the EasyTouch Load Center Removing Electrical Conduit Knockouts Installing Conduit and Wire to the EasyTouch Load Center Installing Conduit and Wire to the EasyTouch Load Center EasyTouch Motherboard Connections Accessing the EasyTouch Motherboard Installing Auxiliary Relays Installing Valve Actuators Solar Temperature Sensor Optional Installing and Connecting Temperature SensorsWater Temperature Sensor Ambient Air Temperature Freeze Protection SensorConnecting the Heater Thermostat Connecting the IntelliChlor Cell Retaining Screws IntelliChlor transformer and filter Rewiring the IntelliChlor Transformer for 115 VACEasyTouch System Start-Up Check ElectronicsEasyTouch System Test Verifying IntelliChlor power EasyTouch System Wiring Diagram Glossary Page 520583 Rev B

8 and 4 specifications

Pentair is renowned for its innovative solutions in water and fluid management, and the Pentair 8 and 4 series are prime examples of their commitment to delivering high-performance products. These series are designed for both residential and commercial applications, showcasing advanced features and technologies that cater to diverse needs.

The Pentair 8 series is known for its robust performance and reliability. It incorporates a powerful motor designed to ensure efficient water circulation and filtration. The 8 series stands out with its user-friendly interface, enabling effortless adjustments and monitoring. The built-in diagnostic features provide real-time feedback, ensuring users can maintain optimal operation without ongoing manual checks. Additionally, the Pentair 8 series emphasizes energy efficiency, reducing power consumption and lowering operational costs.

On the other hand, the Pentair 4 series focuses on compactness and versatility. It is engineered to fit in tight spaces, making it an ideal choice for urban environments where space is a premium. Though smaller in size, the 4 series does not compromise on performance. It utilizes innovative pump technology that maximizes flow while minimizing noise levels. This feature is particularly beneficial for residential applications, where maintaining a quiet environment is essential. The 4 series also includes a range of customizable options, allowing users to tailor the system to their specific requirements.

Both the 8 and 4 series share a commitment to durability and longevity. They are constructed with high-quality materials designed to withstand harsh environmental conditions. This durability reduces the frequency of maintenance and replacement, ultimately providing better value to users.

In summary, the Pentair 8 and 4 series offer a blend of performance, efficiency, and adaptability. Their advanced features, such as energy-efficient motors, user-friendly interfaces, and robust construction, make them suitable for a variety of applications. Whether for residential or commercial use, Pentair continues to set the standard in water management solutions, ensuring both convenience and peace of mind for users. To meet the diverse needs of its clientele, Pentair consistently innovates, ensuring their products remain at the forefront of technology and sustainability.
Top Page Image Contents