SOYO SOYOTM manual Setting, Chars/Sec

Page 28

24	BIOS Setup

Boot Sequence Choose the boot device sequence as your need. For example, ÒA, C, SCSIÓ means BIOS will look for an operating system first from drive A, drive C, then SCSI device. Options of this function are:

A, C, SCSI

C, A, SCSI

C, CDÐROM, A

CDÐROM, C, A

D, A, SCSI

E, A, SCSI

F, A, SCSI

SCSI, A, C

SCSI, C, A

C only.

Swap Floppy Enabled changes the sequence of the drive A and

Drive drive B to drive B and drive A. (The Default setting is Disabled.)

Boot Up Num Choose On or Off. On puts numeric keypad in Num

Lock Status Lock mode at boot-up. Off puts this keypad in arrow key mode at boot-up.

Typematic Rate Enable this option to adjust the keystroke repeat rate.

Setting

Typematic Rate Choose the rate a character keeps repeating.

(Chars/Sec)

Typematic Choose how long after you press a key that a Delay (Msec) character begins repeating.

Security Option Choose Setup or System. Use this feature to prevent unauthorized system boot-up or use of BIOS Setup.

ÒSystemÓ Ð Each time the system is booted the password prompt appears.

ÒSetupÓÐ If a password is set, the password prompt only appears if you attempt to enter the Setup program.

Image 28

Contents 5XA5 TX P54C/P55C PCI Mainboard User’s Guide Technical ReferenceSoyotm Table of Contents Page Introduction Electrostatic Discharge Precautions Unpacking the MainboardMainboard Layout w/ Default Settings TAG SramMainboard Default Setting JP5 Cmos Clear Jumper JumpersJP40 CE Test Jumper Pin JP2 Smart Detect CPU Voltage Function Auto/Manual Jumper JP37 Dimm Voltage Select JumperCPU Type Configuration Frequency SettingHardware Setup Ð1Ð3. CPU Jumper Settings P54C/P55C- 180/60 MHz Socket AMD K6 PR266 CPU Setting 4.0 x clock CPU Single/Dual Voltage Setting Single Voltage CPU SettingMemory Configuration Dual Voltage CPU SettingCache Configuration Memory Configuration TableRAM Bank Installation Notice Cache Size and RAM LocationsMulti I/O Port Addresses FDC FDC Connector JP43 CPU Cooling Fan ConnectorATX PW ATX Power Supply Connectors Reset Hardware Reset Control HDD LED HDD LED ConnectorIDE1/IDE2 On-board Primary/Secondary IDE HDD Connectors IR1 IR ConnectorPS/2 Mouse Conn. PS/2 Mouse Connector PRT Parallel Port ConnectorSPK Speaker Connector USB1/USB2 Universal Serial Bus ConnectorsBios Setup Standard Cmos Setup Bios Setup Drive a & B Video Halt OnBios Features Setup Quick PowerCPU Internal CacheSetting Chars/SecPCI/VGA Dram 64MBChipset Features Setup ROM PCI/ISA Bios Chipset Features Setup Award SOFTWARE, INCDram Timing Dram Leadoff TimingEDO/FP Sdram CASMemory Hole At 15M- Choose Enabled or Disabled default Power Management SetupROM PCI/ISA Bios Cmos Setup Utility Power Management Setup APM Bttn PNP/PCI Configuration Setup Floppy Disk Choose Enabled or Disabled Serial PortPrimary/Secondary IDEPCI IDE IRQ PCI IRQINT# Load Setup Defaults Load Bios DefaultsROM PCI/ISA Bios Integrated Peripherals Award SOFTWARE, INC Integrated PeripheralsPIO IDE Secondary Slave PIOUdma IR Transmission Delay FIR Mode Use DMAParallel Port Mode ECP Mode Use DMAÒEnter PasswordÓ Supervisor PasswordÒConfirm PasswordÓ User Password IDE HDD Auto Detection ROM PCI/ISA Bios Cmos Setup UtilityHard Disks Appendix CPU Setting List CPU Setting List Voltage Setting Possible CPUsMemory Configuration CPU System Hardware Monitor Spread SpectrumESC