SnapGear 1.7.8 manual Internet link features, LAN link features, Dial-in connection features

Page 13

Internet link features

•Connect to the Internet using an external cable modem, DSL, dial-up or ISDN modem.

•Serial ports connect to the Internet using an external modem or ISDN T/A. The LITE2, LITE2+, SME530 and SME550 models have a single serial port.

•10baseT Ethernet port (Internet) that connect to the Internet using a cable or ADSL modem.

•Front panel serial status LEDs (for TXD/RXD).

•Online status LEDs (for Internet/VPN).

•Rear panel Ethernet LEDs (Link Transmit/Receive).

LAN link features

•10/100BaseT LAN port to connect to the local network Ethernet on PRO+, LITE2, LITE2+, SME530 and SME550 models, 10BaseT on other models.

•Rear panel Ethernet LEDs (Link Transmit/Receive) on all models but LITE2 and LITE2+.

Dial-in connection features

If you are using the SnapGear PRO+, PRO, SOHO+, SME530 or SME550, external modems may be attached via serial port for dial-in connections. Additionally, the SnapGear PRO+ has an internal modem that can be used for dial-in connections.

10

Introduction

Image 13

Contents Rev May 2nd Table of contents Virtual Private Networking Introduction Term Meaning TerminologyLAN TCP/IP Document conventionsStep Chapter Installing and configuring your SnapGear applianceLEDs Your SnapGear applianceLabel Activity Description SnapGear appliance back panels Network interconnections Software features SnapGear appliance featuresLAN link features Internet link featuresDial-in connection features Environmental features Getting started Static IP reset10.0.0.0 10.255.255.255 10/8 prefix New Networks192.168.0.0 192.168.0.255 192.168.0/24 prefix Configuring the SnapGear appliance on your network Page Set up IP addresses Multiple SnapGear appliances were found on the network Your SnapGear appliance was found on the networkYour SnapGear appliance needs an IP address SnapGear Management Console web administration pages Administrative passwordUsing linsetip Initial setup using LinuxPing -b subnet broadcast address Arp -a Using an existing local Dhcp or Bootp serverEdit the /etc/inetd.conf file Configuring a new local Dhcp or Bootp serverSnapGear Quick Setup LAN port quick setup LAN port quick setupISP connection quick setup ISP connection quick setupGetting started Configuring the PCs on your network TCP/IP properties Physically connect modem device Connecting to the InternetConnect to Internet cable modem Select Internet connectionConnect to Internet Adsl Connect to Internet modem Connect to Internet directField Description ISP. The Password and Confirm Password fields mustInternet failover Advanced configuration optionFollowing figure shows the failover configuration screen Failed connection Establishing the connection Configure PCs to use SnapGear appliance Internet gatewayDial-in server configuration Dial-in server configuration Dial-in setup Dial-in setupField Description Dial-in user account creation Dial-in user accountsFollowing figure shows the user maintenance screen Account list Dial-in password errorFor Windows 95 and Windows Remote user configurationServer types Connect to dialogue box WindowsClick Next to continue 11 Connection availability 13 Remote access login screen IP configuration Network configurationNetwork configuration Advanced IP configuration Advanced IP configurationNetwork configuration Dhcp server Dhcp server configurationNetwork configuration Traffic shaping Advanced networkingAdditional routes Firewall Incoming accessIncoming access configuration Incoming access administration servicesConfigure external access to services External access to servicesPort forwarding Port forwarding configurationSecurity group classes configuration Outgoing accessFirewall rules Outgoing access settingsIntrusion detection and blocking Intrusion detection and blocking configurationPage Content filtering Content filtering Filtering Level Description Filtering levels and reportingVirtual Private Networking 1VPN tunneling using the Pptp serverPptp client setup Pptp client configuration Pptp server setup Pptp server setup Enable and configure the Pptp VPN serverField Description 4PPTP VPN server accounts screen Configuring user accounts for VPN serverVirtual Private Networking VPN Pptp IP address Configuring the remote VPN clientVirtual Private Networking Windows 95 and Windows VPN client setupYour VPN client is now set up correctly Windows NT Network and dial-up connections This displays the Destination Address window Connecting the remote VPN client 12 IPSec setup IPSec setup13 Add new IPSec connection Virtual Private Networking 14 Automatic keying setup Technique Description Aggressive mode phase 1 settingsIPSec interoperability System PasswordTime server Advanced DiagnosticsReset button Flash upgradeTechnical support Technical supportLED Pattern Status Action Appendix a LED status patternsAppendix B System Log Access LoggingEth0 Default DenyEth1 PppCreating Custom Log Rules Forward Iptables -I Forward -j LOG -i eth+ -o eth+ -p tcp Rate Limiting Administrative Access LoggingBoot Log Messages