SnapGear 1.7.8 manual Your SnapGear appliance was found on the network

Page 21

A.Your SnapGear appliance was found on the network.

This means either your network is DHCP enabled and another PC on the network has already given it an IP address, or you have chosen to boot the SnapGear appliance with an initial, static IP address. If this is the case, skip to Administrative Password further on in this chapter.

B.Multiple SnapGear appliances were found on the network.

This means your network is DHCP enabled. If this is the case, SnapGear Setup Wizard will prompt you to select which SnapGear VPN Router you wish to configure, based on its LAN port MAC address. The SnapGear Setup Wizard will display each of the different SnapGear VPN Routers that were found on the network. When the appropriate one is displayed, click "Yes" to indicate that this is the unit you want to configure. Your SnapGear VPN Router's LAN port MAC address is printed on its underside of the unit. Make the appropriate selection, then skip to Administrative Password further on in this chapter.

18

Getting started

Image 21

Contents Rev May 2nd Table of contents Virtual Private Networking Introduction Term Meaning TerminologyLAN TCP/IP Document conventionsStep Chapter Installing and configuring your SnapGear applianceYour SnapGear appliance LEDsLabel Activity Description SnapGear appliance back panels Network interconnections Software features SnapGear appliance featuresInternet link features LAN link featuresDial-in connection features Environmental features Getting started Static IP reset10.0.0.0 10.255.255.255 10/8 prefix New Networks192.168.0.0 192.168.0.255 192.168.0/24 prefix Configuring the SnapGear appliance on your network Page Set up IP addresses Multiple SnapGear appliances were found on the network Your SnapGear appliance was found on the networkYour SnapGear appliance needs an IP address SnapGear Management Console web administration pages Administrative passwordUsing linsetip Initial setup using LinuxPing -b subnet broadcast address Arp -a Using an existing local Dhcp or Bootp serverEdit the /etc/inetd.conf file Configuring a new local Dhcp or Bootp serverSnapGear Quick Setup LAN port quick setup LAN port quick setupISP connection quick setup ISP connection quick setupGetting started Configuring the PCs on your network TCP/IP properties Physically connect modem device Connecting to the InternetSelect Internet connection Connect to Internet cable modemConnect to Internet Adsl Connect to Internet modem Connect to Internet directField Description ISP. The Password and Confirm Password fields mustInternet failover Advanced configuration optionFollowing figure shows the failover configuration screen Failed connection Establishing the connection Configure PCs to use SnapGear appliance Internet gatewayDial-in server configuration Dial-in server configuration Dial-in setup Dial-in setupField Description Dial-in user account creation Dial-in user accountsFollowing figure shows the user maintenance screen Account list Dial-in password errorFor Windows 95 and Windows Remote user configurationServer types Connect to dialogue box WindowsClick Next to continue 11 Connection availability 13 Remote access login screen IP configuration Network configurationNetwork configuration Advanced IP configuration Advanced IP configurationNetwork configuration Dhcp server Dhcp server configurationNetwork configuration Advanced networking Traffic shapingAdditional routes Firewall Incoming accessIncoming access configuration Incoming access administration servicesConfigure external access to services External access to servicesPort forwarding Port forwarding configurationSecurity group classes configuration Outgoing accessFirewall rules Outgoing access settingsIntrusion detection and blocking Intrusion detection and blocking configurationPage Content filtering Content filtering Filtering Level Description Filtering levels and reportingVirtual Private Networking 1VPN tunneling using the Pptp serverPptp client setup Pptp client configuration Pptp server setup Pptp server setup Enable and configure the Pptp VPN serverField Description 4PPTP VPN server accounts screen Configuring user accounts for VPN serverVirtual Private Networking VPN Pptp IP address Configuring the remote VPN clientVirtual Private Networking Windows 95 and Windows VPN client setupYour VPN client is now set up correctly Windows NT Network and dial-up connections This displays the Destination Address window Connecting the remote VPN client 12 IPSec setup IPSec setup13 Add new IPSec connection Virtual Private Networking 14 Automatic keying setup Technique Description Aggressive mode phase 1 settingsIPSec interoperability Password SystemTime server Advanced DiagnosticsReset button Flash upgradeTechnical support Technical supportLED Pattern Status Action Appendix a LED status patternsAppendix B System Log Access LoggingEth0 Default DenyEth1 PppCreating Custom Log Rules Forward Iptables -I Forward -j LOG -i eth+ -o eth+ -p tcp Rate Limiting Administrative Access LoggingBoot Log Messages