SnapGear 1.7.8 manual Your SnapGear appliance needs an IP address

Page 22

C.Your SnapGear appliance needs an IP address.

This means your network is not DHCP enabled and you must perform the following steps:

Enter the IP address that you want to assign to your SnapGear appliance. SnapGear Setup Wizard will already have auto-completed the IP address. Verify that this address is acceptable and not already in use, and click OK.

SnapGear Setup Wizard will check that the IP address you selected isn't already in use. If it is you will be asked to make a new selection, otherwise it is assigned to your SnapGear appliance. Note that this may take a few seconds.

Your SnapGear VPN Router is now set up with an IP address so all front panel LEDs (except System/TST/Heart Beat) will stop flashing.

19

Getting started

Image 22

Contents Rev May 2nd Table of contents Virtual Private Networking Introduction Terminology Term MeaningLAN Document conventions TCP/IPInstalling and configuring your SnapGear appliance Step ChapterLEDs Your SnapGear applianceLabel Activity Description SnapGear appliance back panels Network interconnections SnapGear appliance features Software featuresLAN link features Internet link featuresDial-in connection features Environmental features Static IP reset Getting startedNew Networks 10.0.0.0 10.255.255.255 10/8 prefix192.168.0.0 192.168.0.255 192.168.0/24 prefix Configuring the SnapGear appliance on your network Page Set up IP addresses Your SnapGear appliance was found on the network Multiple SnapGear appliances were found on the networkYour SnapGear appliance needs an IP address Administrative password SnapGear Management Console web administration pagesInitial setup using Linux Using linsetipUsing an existing local Dhcp or Bootp server Ping -b subnet broadcast address Arp -aConfiguring a new local Dhcp or Bootp server Edit the /etc/inetd.conf fileSnapGear Quick Setup LAN port quick setup LAN port quick setupISP connection quick setup ISP connection quick setupGetting started Configuring the PCs on your network TCP/IP properties Connecting to the Internet Physically connect modem deviceConnect to Internet cable modem Select Internet connectionConnect to Internet Adsl Connect to Internet direct Connect to Internet modemISP. The Password and Confirm Password fields must Field DescriptionAdvanced configuration option Internet failoverFollowing figure shows the failover configuration screen Failed connection Configure PCs to use SnapGear appliance Internet gateway Establishing the connectionDial-in server configuration Dial-in server configuration Dial-in setup Dial-in setupField Description Dial-in user accounts Dial-in user account creationFollowing figure shows the user maintenance screen Dial-in password error Account listRemote user configuration For Windows 95 and WindowsServer types Windows Connect to dialogue boxClick Next to continue 11 Connection availability 13 Remote access login screen Network configuration IP configurationNetwork configuration Advanced IP configuration Advanced IP configurationNetwork configuration Dhcp server configuration Dhcp serverNetwork configuration Traffic shaping Advanced networkingAdditional routes Incoming access FirewallIncoming access administration services Incoming access configurationExternal access to services Configure external access to servicesPort forwarding configuration Port forwardingOutgoing access Security group classes configurationOutgoing access settings Firewall rulesIntrusion detection and blocking configuration Intrusion detection and blockingPage Content filtering Content filtering Filtering levels and reporting Filtering Level Description1VPN tunneling using the Pptp server Virtual Private NetworkingPptp client setup Pptp client configuration Pptp server setup Enable and configure the Pptp VPN server Pptp server setupField Description Configuring user accounts for VPN server 4PPTP VPN server accounts screenVirtual Private Networking Configuring the remote VPN client VPN Pptp IP addressVirtual Private Networking VPN client setup Windows 95 and WindowsYour VPN client is now set up correctly Windows NT Network and dial-up connections This displays the Destination Address window Connecting the remote VPN client IPSec setup 12 IPSec setup13 Add new IPSec connection Virtual Private Networking 14 Automatic keying setup Aggressive mode phase 1 settings Technique DescriptionIPSec interoperability System PasswordTime server Diagnostics AdvancedFlash upgrade Reset buttonTechnical support Technical supportAppendix a LED status patterns LED Pattern Status ActionAccess Logging Appendix B System LogEth1 Default DenyEth0 PppCreating Custom Log Rules Forward Iptables -I Forward -j LOG -i eth+ -o eth+ -p tcp Administrative Access Logging Rate LimitingBoot Log Messages