Uniden UBCT9 manual Connecting the Power Cord Installation for everyday use

Page 13

3.Drill the necessary holes and secure the mounting bracket in place using the screws provided.

4.Mount the radio to the bracket only after the wiring has been connected to the rear panel.

Connecting the Power Cord

Note: If you are not experienced in connecting accessories to the vehicle fuse box, please see your automotive dealer for advice on proper installation.

Installation for everyday use:

1.Check the vehicle battery connections to determine which battery terminal (positive or negative) is grounded to the engine block or chassis. Most of today’s vehicles use a negative ground. If your vehicle has a negative ground, follow Steps 2 and 3. Otherwise, skip to the note following Step 3.

2.Connect the RED wire of the DC power cord to the accessory contact in your vehicle’s +12V DC fuse box.

3.Connect the BLACK wire of the DC power cord to the negative side of the vehicle (usually the chassis).

Note: In vehicles with a positive ground, the RED wire connects to the chassis and the BLACK wire connects to the accessory contact in the fuse box.

4. Insert the DC plug into the DC 12V jack on the back of the scanner.

UBCT9 OM 9

12/11/07 3:52:27 PM

Image 13

Contents UBCT9 Scanner Precautions Contents Edacs Introduction Range Mhz Mode StepSelector SQL, Flash Front and Rear ViewsNumber 1 2 3 4 Icon DisplayWhat is Searching? What is Scanning?What is Trunk Tracking? TerminologyUBCT9 OM Feature Highlights Included with Your Scanner Package Optional AccessoriesFor Home Use Desktop Installation Installing the UBCT9For Mobile Use In-Car Installation Connecting the Power Cord Installation for everyday use Mounting the Scanner in Your Vehicle Typical Mounting MethodsDC power Installation Applying Power for Vehicle InstallationConnecting an External Speaker Applying Power Using Standard AC PowerConnecting the Clone Cable Listening SafelyTurn the Scanner On Scanning OverviewHow Squelch Works Setting the SquelchSelecting the State State ScanningPress Police Storing State Scan Frequencies State Scan HoldSkip a frequency Close Call RF Capture Set Close Call ModeClose Call Operation Select Close Call Bands Set Close Call OptionAlert Tone Volume Setting of pager screenAlert Light Adjustment Set Close Call AlertProgramming Frequencies into Channels Private Bank ScanningDeleting a Stored Frequency Memory Lock Duplicate Frequency AlertScanning Private Bank Hold/Resume Restoring a Locked-out Channel in Hold ModeChannel Lockout Priority Scan Restoring All Locked-out ChannelsChanging the Priority Channel Then press HOLD/RESUMEPolice Rail Roads Aircraft Marine Band UHF CB Band Service ScanningMode Step Display Setting a Search BandBand Search Band NoData Skip Search Hold FeatureFrequency Skip Storing Search Frequencies DelayTrunk Tracking Selecting Trunking System Type Programming Trunking FrequenciesProgramming Talk Group ID/Scan Lists Programming Trunking FrequenciesTo enter a Type 1 ID To enter a Type 2 Talk Group IDTo enter a Full Edacs ID To enter a Partial Edacs IDReceiving Trunked Systems ID Scan ModeID Search Mode ID Scan Hold FeatureTo directly access a specific ID location ID Search Hold and Direct Entry ID in Hold Mode ID Monitor ModeProgramming Scan Lists During Search Deleting a Stored IDTo restore all locked out IDs in a bank once To restore a single ID, follow these stepsID Lockout Review ID LockoutSetting Priority in Trunking Mode Setting the Delay Mode for Trunking ModeTrunking Frequency Confirmation Moving between Scan List MemoriesMulti-Track Operational Details Multi-TrackEdacs Tracking Edacs ReceptionProgramming Edacs System Frequencies Format An Edacs Trunked systemEdacs ID Range Search Special Edacs FeaturesLTR Tracking LTR ReceptionMotorola Tracking Motorola ReceptionFleet Map Programming Selecting Preset Fleet MapProgramming a User Fleet Map Programming a Hybrid System Toggling the Status Bit Control Channel Only ModeDisconnect Tone Detect Option End Code Remote Interface PC Control ModePC Control Parameter Clone ModeFor your information To connect the Scanner to Scanner 12/11/07 35404 PM General Use Care and MaintenanceProblem Suggestion Troubleshooting12/11/07 35405 PM Specifications State Code Order State Name AppendixPreset Fleet Maps 12/11/07 35407 PM Type I Programming Information User Defined Fleet MapsFleet Map Size Codes Size Code Restrictions Memo Memo Uniden UBCT9 Scanning Receiver One Year Limited WarrantyFax 02 9599 Fax 09 274 Thank YOU for Buying a Uniden Product