Uniden UBCT9 Restoring All Locked-out Channels, Priority Scan, Changing the Priority Channel

Page 28

Restoring All Locked-out Channels

You can restore all locked-out channels in a bank only when a bank is selected for scan. If you have deselected a bank and you want to restore all of its locked-out channels using the steps below, you must press SCAN until “SCAN ” appears and then enter the number of the bank on your keypad.

1.Press HOLD/RESUME.

Note: You must be in Hold mode before restoring all locked-out channels.

2.Press and hold L/O for about 2 seconds. You will hear two beeps when all the channels have been restored.

Priority Scan

When Priority Scan is turned ON, your scanner checks the priority channel in the banks you selected every two seconds for activity. If a signal is present on the priority channel, your scanner monitors the channel until the transmission ends, then resumes normal scanning.

You can designate one channel in each bank as a Priority Channel. By default, the first channel in each bank is the Priority Channel, but you can change this.

To activate Priority Scan (in either the Hold or Scan mode):

SCAN

1. Press PRI. “PRI ” appears.

Note: If you have locked out the priority channel, error message appears when you select Priority mode.

SCAN

2. Press PRI again to deactivate Priority Scan. “PRI ” disappears.

Changing the Priority Channel

You cannot eliminate the Priority Channel, but you can change it to any one of the 50 available channels in each bank.

1.Press HOLD/RESUME.

2.Select a new Priority Channel:

a.Enter the channel number using the keypad.

b.Then press HOLD/RESUME.

3. Press and hold PRI for 2 seconds to designate this channel

as your new Priority Channel.

SCAN

 

When you hear two beeps, the Priority Channel has been

 

changed. “ P” appears on the display.

Note: Priority in Trunking mode works just the same, except you set them for talkgroup IDs instead of setting priorities for channels. The scanner only checks priority talkgroups between transmission.

24

UBCT9 OM 24

12/11/07 3:53:41 PM

Image 28
Contents UBCT9 Scanner Precautions Contents Edacs Range Mhz Mode Step IntroductionFront and Rear Views Selector SQL, FlashIcon Display Number 1 2 3 4What is Scanning? What is Searching?What is Trunk Tracking? TerminologyUBCT9 OM Feature Highlights Optional Accessories Included with Your Scanner PackageFor Home Use Desktop Installation Installing the UBCT9For Mobile Use In-Car Installation Connecting the Power Cord Installation for everyday use Typical Mounting Methods Mounting the Scanner in Your VehicleApplying Power for Vehicle Installation DC power InstallationApplying Power Using Standard AC Power Connecting an External SpeakerConnecting the Clone Cable Listening SafelyScanning Overview Turn the Scanner OnSetting the Squelch How Squelch WorksSelecting the State State ScanningPress Police Storing State Scan Frequencies State Scan HoldSkip a frequency Set Close Call Mode Close Call RF CaptureClose Call Operation Set Close Call Option Select Close Call BandsSetting of pager screen Alert Tone VolumeAlert Light Adjustment Set Close Call AlertProgramming Frequencies into Channels Private Bank ScanningDeleting a Stored Frequency Memory Lock Duplicate Frequency AlertScanning Private Bank Hold/Resume Restoring a Locked-out Channel in Hold ModeChannel Lockout Restoring All Locked-out Channels Priority ScanChanging the Priority Channel Then press HOLD/RESUMEService Scanning Police Rail Roads Aircraft Marine Band UHF CB BandSetting a Search Band Mode Step DisplayBand Search Band NoData Skip Search Hold FeatureFrequency Skip Delay Storing Search FrequenciesTrunk Tracking Programming Trunking Frequencies Selecting Trunking System TypeProgramming Trunking Frequencies Programming Talk Group ID/Scan ListsTo enter a Type 2 Talk Group ID To enter a Type 1 IDTo enter a Full Edacs ID To enter a Partial Edacs IDID Scan Mode Receiving Trunked SystemsID Search Mode ID Scan Hold FeatureTo directly access a specific ID location ID Monitor Mode ID Search Hold and Direct Entry ID in Hold ModeProgramming Scan Lists During Search Deleting a Stored IDTo restore a single ID, follow these steps To restore all locked out IDs in a bank onceID Lockout Review ID LockoutSetting the Delay Mode for Trunking Mode Setting Priority in Trunking ModeTrunking Frequency Confirmation Moving between Scan List MemoriesMulti-Track Multi-Track Operational DetailsEdacs Tracking Edacs ReceptionProgramming Edacs System Frequencies An Edacs Trunked system FormatSpecial Edacs Features Edacs ID Range SearchLTR Reception LTR TrackingMotorola Reception Motorola TrackingFleet Map Programming Selecting Preset Fleet MapProgramming a User Fleet Map Programming a Hybrid System Control Channel Only Mode Toggling the Status BitDisconnect Tone Detect Option End Code PC Control Mode Remote InterfacePC Control Parameter Clone ModeFor your information To connect the Scanner to Scanner 12/11/07 35404 PM Care and Maintenance General UseTroubleshooting Problem Suggestion12/11/07 35405 PM Specifications Appendix State Code Order State NamePreset Fleet Maps 12/11/07 35407 PM User Defined Fleet Maps Type I Programming InformationFleet Map Size Codes Size Code Restrictions Memo Memo Uniden UBCT9 Scanning Receiver One Year Limited WarrantyFax 02 9599 Fax 09 274 Thank YOU for Buying a Uniden Product