Uniden Complete Guide to Starting Remote Mode and Adjusting Transfer Speed for Your Trunking System Scanner
Page 53

Start Remote Mode and Change Transfer Speed:

1.

Press and hold RMT for 2 seconds to activate the Remote

 

mode.

 

2.

Select the transfer speed except for

, then press E and

 

the scanner will start Remote mode.

 

A unique feature of the UBCT8 is that all the front panel keys on the radio remain operational in Remote mode.

For information on purchasing UBCT8 Scanner software to program and control your UBCT8,

you can contact the following:

UNIDEN AUSTRALIA PTY

UNIDEN NEW ZEALAND

LIMITED

 

LIMITED

SERVICE DIVISION

 

SERVICE DIVISION

345 Princes Highway,

 

150 Harris Road,

Rockdale,

 

East Tamaki,

NSW 2216,

 

Auckland,

AUSTRALIA

 

NEW ZEALAND

Fax: (02) 9599 3278

 

Fax: (09) 274 4253

www.uniden.com.au

 

www.uniden.co.nz

PC Control Parameter

 

For your information:

: 9600/19200/38400/57600 bps (adjustable)

Transfer speed

Start/Stop bit

: 1 bit, 1 bit

 

Data Length

: 8 bit

 

Parity Check

: None

 

Code

: ASCII code

 

Flow Control

: None

 

Return Code

: Carriage Return only

Clone Mode

You will need to purchase a RS232C straight cable a null modem adapter. RS232C straight cables are available as male to male or male to female. Even if the RS232C straight cable you buy already has the male to male connectors, you will still have to have the null modem adapter. On the next page you will see the pin connections that are internal to a standard device. (These items are available at your local electronics stores.)

Page 52 Page 54
Image 53
Page 52 Page 54
Contents UBCT8 Scanner Precautions Contents Edacs Scat Introduction Range Mhz Mode StepProg Front and Rear Views3 4 Icon DisplayWhat is Searching? What is Scanning?What is Trunk Tracking? TerminologyPage Feature Highlights Included with Your Scanner Package Optional AccessoriesFor Mobile Use In-Car Installation Installing the UBCT8For Home Use Desktop Installation Connecting the Power Cord Installation for everyday use Mounting the Scanner in Your Vehicle Typical Mounting MethodsDC power Installation Applying Power for Vehicle InstallationConnecting an External Speaker Applying Power Using Standard AC PowerConnecting the Clone Cable Listening SafelyYou can scan in one of five ways Scanning OverviewTurn the Scanner On How Squelch Works Setting the SquelchPress Police State ScanningSelecting the State Skip a frequency State Scan HoldStoring State Scan Frequencies Close CallTM RF Capture Set Close Call ModeClose Call Operation Select Close Call Bands Set Close Call OptionAlert Tone Volume Setting of pager screenAlert Light Adjustment Set Close Call AlertDeleting a Stored Frequency Private Bank ScanningProgramming Frequencies into Channels Scanning Private Bank Duplicate Frequency AlertMemory Lock Channel Lockout Restoring a Locked-out Channel in Hold ModeHold/Resume Priority Scan Restoring All Locked-out ChannelsChanging the Priority Channel Then press HOLD/RESUMEUCB, AM CB ACB Service ScanningBand Search Band No Range Mhz Mode Step DisplayFrequency Skip Search Hold FeatureData Skip Storing Search Frequencies DelayTrunk Tracking Setting the SquelchSelecting Trunking System Type Programming Trunking FrequenciesProgramming Talk Group ID/Scan Lists Programming Trunking FrequenciesTo enter a Type 1 ID To enter a Type 2 Talk Group IDTo enter a Full Edacs ID To enter a Partial Edacs IDReceiving Trunked Systems ID Scan ModeTo directly access a specific ID location ID Scan Hold FeatureID Search Mode ID Search Hold and Direct Entry ID in Hold Mode ID Monitor ModeProgramming Scan Lists During Search Deleting a Stored IDID is restored and L/O disappears To restore a single ID, follow these stepsID Lockout Review ID LockoutSetting Priority in Trunking Mode Setting the Delay Mode for Trunking ModeTrunking Frequency Confirmation Moving between Scan List MemoriesMulti-Track Operational Details Multi-TrackProgramming Edacs System Frequencies Edacs ReceptionEdacs Tracking An Edacs Trunked system Edacs ID Range Search Special Edacs FeaturesLTR Tracking LTR ReceptionMotorola Tracking Motorola ReceptionProgramming a User Fleet Map Selecting Preset Fleet MapFleet Map Programming Programming a Hybrid System Toggling the Status Bit Control Channel Only ModeDisconnect Tone Detect Option End Code Remote Interface PC Control ModePC Control Parameter Clone ModeStart Remote Mode and Change Transfer Speed To connect the Scanner to Scanner Page General Use Care and MaintenanceProblem Suggestion TroubleshootingAdjust the squelch for Trunking mode refer to Specifications Appendix Preset Fleet Maps Page Type I Programming Information User Defined Fleet MapsFleet Map Size Codes Size Code Restrictions Memo Memo Parts Covered Thankyou for Buying a Uniden Product
Top Page Image Contents