Uniden UBCT8 owner manual Private Bank Scanning, Programming Frequencies into Channels

Page 25

Private Bank Scanning

Programming Frequencies into Channels

Before the scanner begins Private Bank scanning, you must program a frequency into at least one channel. Visit our website (www.uniden.com.au, www.uniden.co.nz) for information on known frequencies.

You will need to program each frequency into the scanner’s channels in order to hear these

frequencies.

1.

Press HOLD/RESUME and enter the channel

number where you want to store a frequency by

SCAN

using the keypad, then press HOLD/RESUME.

.

Change the channel by using the or key.

2.Enter the frequency you want to store by using the keypad and (decimal key).

3.Press E to store the frequency into the channel.

4.If you want to program another frequencies into the channel, select another channel by using the or key.

SCAN

SCAN

Note: • To clear a mistake while entering the frequency, press (decimal key) repeatedly until the display is cleared.

•If you enter a invalid frequency, an error tone will sound and "Error" appears on the display. To clear the Error message immediately, press (decimal key).

•Even if you don't enter full numbers as a frequency number, the scanner will automatically select the nearest valid frequency.

Deleting a Stored Frequency

To delete a stored frequency: a. Select a channel.

b. Press 0.

c. Then press E.

Note: Channels with no frequencies are automatically locked out.

Image 25

Contents UBCT8 Scanner Precautions Contents Edacs Scat Introduction Range Mhz Mode StepProg Front and Rear Views3 4 Icon DisplayWhat is Searching? What is Scanning?What is Trunk Tracking? TerminologyPage Feature Highlights Included with Your Scanner Package Optional AccessoriesFor Home Use Desktop Installation Installing the UBCT8For Mobile Use In-Car Installation Connecting the Power Cord Installation for everyday use Mounting the Scanner in Your Vehicle Typical Mounting MethodsDC power Installation Applying Power for Vehicle InstallationConnecting an External Speaker Applying Power Using Standard AC PowerConnecting the Clone Cable Listening SafelyTurn the Scanner On Scanning OverviewYou can scan in one of five ways How Squelch Works Setting the SquelchSelecting the State State ScanningPress Police Storing State Scan Frequencies State Scan HoldSkip a frequency Close CallTM RF Capture Set Close Call ModeClose Call Operation Select Close Call Bands Set Close Call OptionAlert Tone Volume Setting of pager screenAlert Light Adjustment Set Close Call AlertProgramming Frequencies into Channels Private Bank ScanningDeleting a Stored Frequency Memory Lock Duplicate Frequency AlertScanning Private Bank Hold/Resume Restoring a Locked-out Channel in Hold ModeChannel Lockout Priority Scan Restoring All Locked-out ChannelsChanging the Priority Channel Then press HOLD/RESUMEUCB, AM CB ACB Service ScanningBand Search Band No Range Mhz Mode Step DisplayData Skip Search Hold FeatureFrequency Skip Storing Search Frequencies DelayTrunk Tracking Setting the SquelchSelecting Trunking System Type Programming Trunking FrequenciesProgramming Talk Group ID/Scan Lists Programming Trunking FrequenciesTo enter a Type 1 ID To enter a Type 2 Talk Group IDTo enter a Full Edacs ID To enter a Partial Edacs IDReceiving Trunked Systems ID Scan ModeID Search Mode ID Scan Hold FeatureTo directly access a specific ID location ID Search Hold and Direct Entry ID in Hold Mode ID Monitor ModeProgramming Scan Lists During Search Deleting a Stored IDID is restored and L/O disappears To restore a single ID, follow these stepsID Lockout Review ID LockoutSetting Priority in Trunking Mode Setting the Delay Mode for Trunking ModeTrunking Frequency Confirmation Moving between Scan List MemoriesMulti-Track Operational Details Multi-TrackEdacs Tracking Edacs ReceptionProgramming Edacs System Frequencies An Edacs Trunked system Edacs ID Range Search Special Edacs FeaturesLTR Tracking LTR ReceptionMotorola Tracking Motorola ReceptionFleet Map Programming Selecting Preset Fleet MapProgramming a User Fleet Map Programming a Hybrid System Toggling the Status Bit Control Channel Only ModeDisconnect Tone Detect Option End Code Remote Interface PC Control ModeStart Remote Mode and Change Transfer Speed Clone ModePC Control Parameter To connect the Scanner to Scanner Page General Use Care and MaintenanceProblem Suggestion TroubleshootingAdjust the squelch for Trunking mode refer to Specifications Appendix Preset Fleet Maps Page Type I Programming Information User Defined Fleet MapsFleet Map Size Codes Size Code Restrictions Memo Memo Parts Covered Thankyou for Buying a Uniden Product