Uniden UBCT8 Hold/Resume, Channel Lockout, Restoring a Locked-out Channel in Hold Mode

Page 27

Hold/Resume

If you want to stop on a channel during scanning, press

HOLD/RESUME.

If you want to resume scanning, press HOLD/RESUME.

Direct channel access:

There are several ways to access a specific channel quickly.

1.Press HOLD/RESUME.

2.Using the keypad, enter the channel number.

3.Press HOLD/RESUME again.

Note: You can also use the SCAN, or key instead of pressing HOLD/RESUME.

SCAN

SCAN

SCAN

Channel Lockout

You can lockout any channel so it is not checked during normal scanning. You can also restore the channel to scanning when you wish.

Lockout in Hold Mode

1.Press HOLD/RESUME and enter the channel number by using the keypad, then press

HOLD/RESUME.

––– OR –––

1.Press HOLD/RESUME and select the channel by using the or key.

2.Press L/O to lockout the channel. “L/O” appears on the display.

Lockout in Scanning Mode

SCAN

If the scanner keeps stopping on a particular channel due to noise or frequent transmissions, you may want to keep that channel from scanning.

1.Wait until the scanner stops on the channel.

2.Then press L/O.

3.The scanner immediately resumes scanning because the locked out channel is no longer in the scanning sequence.

Lockout Tips Write down your locked-out channels and put in a convenient place in case you need to restore them.

Restoring a Locked-out Channel in Hold Mode

1.Press HOLD/RESUME and select the channel number you want to restore by using the keypad, the or key, then press HOLD/RESUME.

2.Press L/O to unlock the channel. The “L/O” disappears.

Image 27
Contents UBCT8 Scanner Precautions Contents Edacs Scat Introduction Range Mhz Mode StepProg Front and Rear Views3 4 Icon DisplayTerminology What is Scanning?What is Searching? What is Trunk Tracking?Page Feature Highlights Included with Your Scanner Package Optional AccessoriesInstalling the UBCT8 For Home Use Desktop InstallationFor Mobile Use In-Car Installation Connecting the Power Cord Installation for everyday use Mounting the Scanner in Your Vehicle Typical Mounting MethodsDC power Installation Applying Power for Vehicle InstallationListening Safely Applying Power Using Standard AC PowerConnecting an External Speaker Connecting the Clone CableScanning Overview Turn the Scanner OnYou can scan in one of five ways How Squelch Works Setting the SquelchState Scanning Selecting the StatePress Police State Scan Hold Storing State Scan FrequenciesSkip a frequency Close CallTM RF Capture Set Close Call ModeClose Call Operation Select Close Call Bands Set Close Call OptionSet Close Call Alert Setting of pager screenAlert Tone Volume Alert Light AdjustmentPrivate Bank Scanning Programming Frequencies into ChannelsDeleting a Stored Frequency Duplicate Frequency Alert Memory LockScanning Private Bank Restoring a Locked-out Channel in Hold Mode Hold/ResumeChannel Lockout Then press HOLD/RESUME Restoring All Locked-out ChannelsPriority Scan Changing the Priority ChannelUCB, AM CB ACB Service ScanningBand Search Band No Range Mhz Mode Step DisplaySearch Hold Feature Data SkipFrequency Skip Storing Search Frequencies DelayTrunk Tracking Setting the SquelchSelecting Trunking System Type Programming Trunking FrequenciesProgramming Talk Group ID/Scan Lists Programming Trunking FrequenciesTo enter a Partial Edacs ID To enter a Type 2 Talk Group IDTo enter a Type 1 ID To enter a Full Edacs IDReceiving Trunked Systems ID Scan ModeID Scan Hold Feature ID Search ModeTo directly access a specific ID location Deleting a Stored ID ID Monitor ModeID Search Hold and Direct Entry ID in Hold Mode Programming Scan Lists During SearchReview ID Lockout To restore a single ID, follow these stepsID is restored and L/O disappears ID LockoutMoving between Scan List Memories Setting the Delay Mode for Trunking ModeSetting Priority in Trunking Mode Trunking Frequency ConfirmationMulti-Track Operational Details Multi-TrackEdacs Reception Edacs TrackingProgramming Edacs System Frequencies An Edacs Trunked system Edacs ID Range Search Special Edacs FeaturesLTR Tracking LTR ReceptionMotorola Tracking Motorola ReceptionSelecting Preset Fleet Map Fleet Map ProgrammingProgramming a User Fleet Map Programming a Hybrid System Toggling the Status Bit Control Channel Only ModeDisconnect Tone Detect Option End Code Remote Interface PC Control ModeClone Mode Start Remote Mode and Change Transfer SpeedPC Control Parameter To connect the Scanner to Scanner Page General Use Care and MaintenanceProblem Suggestion TroubleshootingAdjust the squelch for Trunking mode refer to Specifications Appendix Preset Fleet Maps Page Type I Programming Information User Defined Fleet MapsFleet Map Size Codes Size Code Restrictions Memo Memo Parts Covered Thankyou for Buying a Uniden Product