Weider ER-A220 Operator Maintenance, Case of power failure, Case of printer error

Page 56

OPERATOR MAINTENANCE

1In case of power failure

When power is lost, the machine retains its memory contents and all information on sales entries.

•When power failure is encountered in register idle state or during an entry, the machine returned to the normal state of operation after power recovery.

•When power failure is encountered during a printing cycle, the register prints “========” and then carries out the correct printing procedure after power recovery. (See the sample print.)

2In case of printer error

If the printer runs out of paper, the printer will stall, “PPPPPPPPPP” will appear on the display. Key entries will not be accepted. Referring to “4. Installing and removing the paper roll” in this chapter, install a new roll paper in the proper position, then press the ckey. The printer will print the power failure symbol and resume printing.

If the print head comes up, the printer stalls, “H” will appear on the very left of the display. Key entries will not be accepted. Bring back the print head to the correct position, then press the ckey. The printer will print the power failure symbol and resume printing.

3Cautions in handling the printer and recording paper

Cautions in handling the printer

• If you are not going to use the register for an extended period of time, pull the print head release lever toward you so that the print head is set apart from the plate. (head-up position)

• Avoid the environments of dusty and humid place, direct sunlight and iron powder(a permanent magnet and electromagnet are use in this machine.)

•Use the print head release lever only when necessary.

•Never pull the paper when it is in contact with the print head. First release the head with the print head release lever, and then remove the paper.

•Never touch the surface of the print head.

•Never touch around the print head and the motor during printing or before they have had sufficient time to cool.

Cautions in handling the recording paper (thermal paper)

•Use only the paper specified by SHARP.

•Do not unpack the thermal paper until you are ready to use it.

•Avoid heat. The paper will color at around 70°C.

•Avoid dusty and humid places for storage. Avoid direct sunlight.

•The printed text on the paper can discolor under the conditions of exposure of high humidity and temperature, exposure to the direct sunlight, contact with glue, thinner or a freshly copied blueprint, and heat caused by friction from scratching or other such means.

•Be very careful when handling the thermal paper. If you want to keep a permanent record, copy the printed text with a photocopier.

54

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Manuel D’INSTRUCTIONS Aviso Precaution IntroductionContents Prior to Entries External View PrinterFront view Rear viewKeyboard Standard keyboard layoutKeys and Switches Mode switch and mode keysDrawer lock key Manager key MA Operator key OPMachine state symbols DisplaysOperator display Customer display Pop-up type Number of repeats for repetitive registrationsSetting the date and time Setting the timeProgramming Preparations for ProgrammingSetting the consecutive number Programming the tax rateProgramming for departments Functional programmingKey operation example Unit priceSelection Entry PLU or subdepartment mode Price lookup PLU programmingUnit price and associated department assignment PLU code three digits 1 to Associated departmentPLU/subdepartment mode 10 ∞Programming function parameters for and % keys Programming the discount key amountProgramming the percent rate limitation % Number of digits after decimal point Programming function parameters for e keyCurrency exchange rate entry selection Text programming 018 ≈Programming function parameters for , , î, r and p keys Alphanumeric character code table Code Character¯ É Programming the department textProgramming the PLU text item label Programming the function text068 º List of function textsProgramming the cashier names Programming logo messages042 º Programming foreign currency symbolProgramming domestic currency symbol Programming print format Programming optional feature selectionProgramming various functions Programming receipt print format Programming Euro system settings Programming power saving modeProgramming logo message print format Programming RS-232C interfaceProgramming thermal printer density RS-232C print dataLanguage selection Programming the Auto key Automatic sequencing keyReading stored programs Key sequence for reading stored programSample printouts Programming reportTraining Mode PLU programming reportReading X and Resetting Z of Sales Totals Summary of reading X and resetting Z reportsDaily sales totals Full sales report Sample reportCashier reports Hourly report PLU sales reportIndividual cashier report Sample report Full cashier reportPeriodic consolidation Full sales report Daily net total reportTypes of compulsory cash/cheque declaration Individual cashier reportElectronic Journal Recording journal dataPrinting journal data on the way of a transaction Sample receiptProgramming for Euro PeriodWhen 1 is substituted to a When 2 is substituted to aWhen 3 is substituted to a Optional Programming for the Introduction of EuroCurrency exchange rate Exchange rate entry selection250 Incorrect receipt Cancellation receiptOverride Entries Preparations for entries Power saving modePrior to Entries Error warning Error escape functionRepeat entries EntriesItem entries Single item entries Multiplication entries Single item cash sale Sics entry100 ã 100 ˘ 700 ú Displaying subtotalsFinalization of transaction Cash or cheque tendering Cheque tendering Key operation example Print300 ü 10 Ö 950 É550 ù Automatic VAT 1 and automatic tax 2-4 system140 û 570 ä 800 ü 15 Ö575 ü 10 Ö 100 Auxiliary entries Percent calculations premium or discount675 ä 250 ü 13 ÖRefund entries Printing of non-add code numbersApplying manual exchange rate Key operation example Applying preset exchange rate Key operation examplePayment treatment Currency exchange Received on account entries Paid out entriesNo sale exchange Automatic sequencing key ` key entries850 ˘ 150 ¯ Receipt issuance after finalization/Copy receiptCorrection of the last entry direct void Correction600 ô 328 ã Key operation example Comments Overlapped Cashier EntrySubtotal void Case of printer error Operator MaintenanceCase of power failure Installing and removing the paper roll Installing the paper rollPaper specification How to set the paper roll How to cut the paper endWhen the take-up spool is used Removing the paper rollRemoving the till and the drawer Cleaning the print headRemoving a paper jam Installing the fixing angle bracket How to install the fixing angle bracketHow to remove the register from the fixing angle bracket Opening the drawer by handBefore calling for service Error code tableSpecifications List of OptionsBLUENeutral BROWNLive Environment ProtectionUmweltschutz Protection de l’environnementSharp Corporation
Top Page Image Contents