Weider ER-A220 Installing and removing the paper roll, Installing the paper roll

Page 57
ákey to

4Installing and removing the paper roll

Be sure to use paper rolls specified by SHARP.

The use of any other paper rolls than specified could cause paper jamming, resulting in register malfunction.

Paper specification

 

 

Paper width: 57.5 ± 0.5 mm

Max. outside diameter: 70 mm

Quality: Thermal paper

• Be sure to set paper roll(s) prior to using your machine, otherwise it may cause a malfunction.

Install the paper roll in the printer. Be careful then to set the roll and cut the paper end correctly.

If the top end of the paper roll is fixed with paste or tape, the paper may lose its color development ability in the pasted or taped area due to the deterioration of the heat-sensitive color development component of the paper surface. This may result in nothing appearing at this location when printing is performed. Therefore, when setting a new paper roll in the machine, be sure to cut off approximately one revolution (approx. 25 cm long).

(How to set the paper roll)

(How to cut the paper end)

 

To the printer

To the printer

 

Incorrect

Correct

Incorrect

 

Correct

Installing the paper roll

Precaution: Be very careful for the manual cutter mounted on the printer cover when removing and replacing the cover, so as not to hurt yourself.

When you install a paper roll for the first time, the printer is in printer error status because no paper roll has not installed yet. So, after installing a paper roll correctly, clear the error status by pressing

ckey.

1. Turn the mode switch to the “REG” position with the AC cord connected.

2. Remove the printer cover.

3. Check that the print head release lever is in its printing position.

4. Set the paper correctly as illustrated above in the paper bed.

5. Insert the end of the paper into the printer, while pressing the ákey, until it is caught by the printer auto-feed and comes out of the printer at the top.

6. When not using the take-up spool (using as receipt paper) :

• Cut off the excess paper that comes out of the printer using the edge of the inner cover, and replace the printer cover.

When using the take-up spool (using as journal paper):

• Insert the end of the paper into the slit in the spool. (Press the feed more paper if required.)

• Wind the paper two or three turns around the spool shaft.

• Set the spool on the bearing, and press the ákey to take up excess slack in the paper.

• Replace the printer cover.

You can wind the roll paper in OP X/Z, X1/X2, and X2/Z2 modes even if you programmed so that the printer is used for issuance of receipts. This may be convenient to wind reports. In this case, set the roll paper to the take-up spool.

55

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Manuel D’INSTRUCTIONS Aviso Introduction PrecautionContents Prior to Entries Printer External ViewFront view Rear viewStandard keyboard layout KeyboardMode switch and mode keys Keys and SwitchesDrawer lock key Manager key MA Operator key OPDisplays Machine state symbolsOperator display Customer display Pop-up type Number of repeats for repetitive registrationsSetting the time Setting the date and timeProgramming Preparations for ProgrammingProgramming the tax rate Setting the consecutive numberFunctional programming Programming for departmentsUnit price Selection EntryKey operation example Price lookup PLU programming PLU or subdepartment modeUnit price and associated department assignment PLU code three digits 1 to Associated department10 ∞ PLU/subdepartment modeProgramming the discount key amount Programming the percent rate limitation %Programming function parameters for and % keys Programming function parameters for e key Currency exchange rate entry selectionNumber of digits after decimal point 018 ≈ Programming function parameters for , , î, r and p keysText programming Code Character Alphanumeric character code tableProgramming the department text ¯ ÉProgramming the PLU text item label Programming the function textList of function texts 068 ºProgramming logo messages Programming the cashier namesProgramming foreign currency symbol Programming domestic currency symbol042 º Programming optional feature selection Programming various functionsProgramming print format Programming receipt print format Programming power saving mode Programming Euro system settingsProgramming RS-232C interface Programming logo message print formatRS-232C print data Programming thermal printer densityProgramming the Auto key Automatic sequencing key Language selectionKey sequence for reading stored program Reading stored programsSample printouts Programming reportPLU programming report Training ModeSummary of reading X and resetting Z reports Reading X and Resetting Z of Sales TotalsSample report Daily sales totals Full sales reportHourly report PLU sales report Cashier reportsIndividual cashier report Sample report Full cashier reportDaily net total report Periodic consolidation Full sales reportIndividual cashier report Types of compulsory cash/cheque declarationRecording journal data Electronic JournalPrinting journal data on the way of a transaction Sample receiptPeriod Programming for EuroWhen 2 is substituted to a When 1 is substituted to aOptional Programming for the Introduction of Euro When 3 is substituted to aCurrency exchange rate Exchange rate entry selectionIncorrect receipt Cancellation receipt Override Entries250 Power saving mode Prior to EntriesPreparations for entries Error escape function Error warningEntries Item entries Single item entriesRepeat entries Single item cash sale Sics entry Multiplication entriesDisplaying subtotals 100 ã 100 ˘ 700 úFinalization of transaction Cash or cheque tendering Cheque tendering Key operation example Print950 É 300 ü 10 ÖAutomatic VAT 1 and automatic tax 2-4 system 550 ù800 ü 15 Ö 140 û 570 ä575 ü 10 Ö 100 Auxiliary entries Percent calculations premium or discount250 ü 13 Ö 675 äRefund entries Printing of non-add code numbersApplying preset exchange rate Key operation example Payment treatment Currency exchangeApplying manual exchange rate Key operation example Paid out entries Received on account entriesNo sale exchange Automatic sequencing key ` key entriesReceipt issuance after finalization/Copy receipt 850 ˘ 150 ¯Correction 600 ô 328 ãCorrection of the last entry direct void Overlapped Cashier Entry Subtotal voidKey operation example Comments Operator Maintenance Case of power failureCase of printer error Installing the paper roll Installing and removing the paper rollPaper specification How to set the paper roll How to cut the paper endRemoving the paper roll When the take-up spool is usedCleaning the print head Removing a paper jamRemoving the till and the drawer How to install the fixing angle bracket Installing the fixing angle bracketHow to remove the register from the fixing angle bracket Opening the drawer by handError code table Before calling for serviceList of Options SpecificationsEnvironment Protection BLUENeutral BROWNLiveUmweltschutz Protection de l’environnementSharp Corporation
Top Page Image Contents