X-Micro Tech WLAN 11g user manual Rts

Page 22

	It is case-sensitive and cannot exceed 32
	characters.

Channel	Selects one IEEE 802.11G channel for
	wireless LAN transmissions from the
	drop-down list.
	Specifies the bandwidth which the wireless
	radio operates. AP and the client stations that
	is associated work in one of channels from 1
	to 14.

4.4.1.5. Enter the following advanced radio parameters:

Parameter	Description

Beacon	Type the time interval in milliseconds
Interval	between beacons broadcast by AP
	(Access Point) in the Beacon Interval box,
	such as 100.

RTS	Type a number in the RTS Threshold box.
Threshold	Also called Request-to-Send Threshold.
	Also called Request-to-Send Threshold.
	This field specifies the minimum size of
	data frames above which RTS protocol
	is used, ranging from 256 to 2432. RTS
	helps prevent data collision from hidden
	nodes.

Fragmentatio	Type a number in the Fragmentation
n Threshold	Threshold box.
	For efficiency in high-traffic situations,
	large files are split into fragments. This
	field specifies the default packet size, an
	even number ranging from 256 to 2346.

DTIM Interval	Type a number in the DTIM Interval box.
	Also called Delivery Traffic Indication
	Map. This field specifies the number of
	beacon intervals between successive
	DTIMs, ranging from 1 to 255.

Preamble	Select either Short Preamble (72 bits) or
Type	Long Preamble (144 bits).

Distribution	If you want to use Wireless Distribution
System	System on your Router, click Enable
	next to Distribution System, then type the
	distributed client PCs’ physical
	addresses, as described in Step 6.
	Otherwise, click Disable.

	22

Image 22

Contents Wlan 11g Broadband Router XWL-11GRIX FCC Radiation Exposure Statement USA Federal Communications Commission FCCCopyright DisclaimerContents System Requirements Product FeatureApplications Installing Your Router Installation InstructionsConfiguring Windows for IP Networking To Configure Windows to Receive Dynamic IP AddressPage Collecting ISP Information To Open the Web-based Administration Tool Logon dialog boxType admin in the User Name box Type the password in the box Setup To Configure Setup ParametersPage Page To Set PPPoE Login Parameters Click Enable next to PPPoE LoginTo Set up Global Address with DMZ Disabled Global AddressTo Set up Global Address with DMZ Enabled Global Address Page with DMZ EnabledTo Remove Global Addresses Wireless To Set the Wireless Radio ParametersDescription ModeRTS To Set Wireless Security Parameters Default Values for Radio Settings10 Wireless Security Settings To Set WEP Keys Four newly generated WEP Keys will display in the Key 1 Key To Review Wireless Status On the Wireless page, select StatusTo Disable Wireless To Change the Administrative Password for Your Router ToolsTo Restore the Factory Default Configuration Type the new password in the Confirm Password boxTftp -i gatewayIpaddress GET filename To Reset GatewayTo Upgrade the Firmware Tftp -i gatewayIpaddress PUT filenameUpgraded Status Status Detail Paramet DescriptionDisconnected Dhcp To Set Your Router as a Dhcp ServerTable, seen in Figure To Disable Dhcp on Your RouterTo View the Active IP Table Optional. Click Refresh to obtain the most current dataTo View Session Event Log To Set up Access Log on Your RouterLog Click Session Event Log on the LogTo View Block Event Log To View Intrusion Event LogClick Wireless Event Log on the Log To View Wireless Event LogTo Disable Access Log on Your Router Click Intrusion Event Log on the LogStatistics 25 StatisticsAP Radio Lists out the data on the Access Point’s radio To Toggle between Basic Functions and Advanced Functions Advanced Button on the Basic WindowTo Set up a Client PC on the LAN as a Virtual Server Virtual ServersSelect a Public IP Address from the drop-down list Well-know PortsTo Delete Virtual Servers on the LAN To Set up a Port Filtering or Raw IP Filter FiltersPage Drop-down list Inbound Outbound and Both To Delete Filters To Delete a Port Filtering FilterDo either of the following IP/URL BlockTo Block a Single IP Address IP Block page appears, seen in FigureTo Block a Range of IP Address To Block a Specific Domain NameTo Delete a Specific or All IP Blocks To Delete a Specific or All URL BlocksSpecial Apps To Copy a Popular Application to a Specific LineTo Configure a Special Application Manually Popular Applications ListSpecial Apps Select a line corresponding to a specific ID To Delete Special Applications To Designate a PC in Your Network as a DMZ Host DMZ HostWhat do you want to do? To Delete DMZ Hosts On the Advanced navigation bar, click MAC Clone MAC CloneTo Clone the MAC Address Convenience, seen in FigureTo Configure a Dynamic DNS Server Dynamic DNSTo Disable a Dynamic DNS Server To Configure a Proxy DNS Server Proxy DNSTo Disable the Proxy DNS on Your Router To Delete a Specific or All Proxy DNS ServersSnmp 14 Snmp Enter the following Agent information To Delete an Existing Snmp Trap Receiver To Delete Snmp Community NamesStatic Routing To Add a New Static Route To Delete a Static Route Glossary Ieee WAN